HP rp8420 Installation Guide, Fifth Edition - HP 9000 rp8420 Server - Page 59

Installing the Line Cord Anchor (rack mounted servers), Four Cell Server Installation (rp8400, rp8420

Get HP rp8420 PDF manuals and user guides View all HP rp8420 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Installation Cabling and Power Up Installing the Line Cord Anchor (rack mounted servers) The line cord anchor is attached to the rear of the server when rack mounted. It provides a method to secure the line cords to the server, preventing accidental removal of the cords from the server. Four Cell Server Installation (rp8400, rp8420, rp8440, rx8620, rx8640) There are holes pre-drilled, and captive nuts pre-installed in the server chassis. To install the line cord anchor: 1. Align the line cord anchor thumbscrews with the corresponding captive nuts at the rear of the chassis. See Figure 2-25, "Four Cell Line Cord Anchor (rp8400, rp8420, rp8440, rx8620, rx8640)," Figure 2-25 Four Cell Line Cord Anchor (rp8400, rp8420, rp8440, rx8620, rx8640) 2. Tighten the captive thumbscrews to secure the line cord anchor to the chassis. 3. Weave the power cables through the line cord anchor. Leave enough slack that the plugs can be disconnected from the receptacles without removing the cords from the line cord anchor Chapter 2 59

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
Chapter 2
Installation
Cabling and Power Up
59
Installing the Line Cord Anchor (rack mounted servers)
The line cord anchor is attached to the rear of the server when rack mounted. It provides a method to secure
the line cords to the server, preventing accidental removal of the cords from the server.
Four Cell Server Installation (rp8400, rp8420, rp8440, rx8620, rx8640)
There are holes pre-drilled, and captive nuts pre-installed in the server chassis.
To install the line cord anchor:
1. Align the line cord anchor thumbscrews with the corresponding captive nuts at the rear of the chassis.
See Figure 2-25, “Four Cell Line Cord Anchor (rp8400, rp8420, rp8440, rx8620, rx8640),”
Figure 2-25
Four Cell Line Cord Anchor (rp8400, rp8420, rp8440, rx8620, rx8640)
2. Tighten the captive thumbscrews to secure the line cord anchor to the chassis.
3. Weave the power cables through the line cord anchor. Leave enough slack that the plugs can be
disconnected from the receptacles without removing the cords from the line cord anchor