HP xp7030 User Guide - Page 40

Replacing the lamp module - digital projector lamp

Get HP xp7030 - Digital Projector PDF manuals and user guides View all HP xp7030 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Replacing the lamp module As the projector operates over time, the brightness of the projector lamp gradually decreases and the lamp becomes more susceptible to breakage. You can install a new lamp at any time to bring the projector up to factory-fresh brightness. We recommend replacing the lamp if a warning message is displayed. WARNING! Replacing the lamp module requires special consideration: • To reduce the risk of injury, be careful when removing the lamp module as broken glass might be present. HP also recommends wearing goggles and gloves when removing the lamp module. If the lamp is broken, contact HP about repairs that might be required due to glass fragments. • The lamp in this digital projector contains mercury. If the lamp breaks, adequately ventilate the immediate area, discard any nearby food and drink, and thoroughly clean the table surface around the projector. Wash your hands after cleaning the area or handling a broken lamp. Note that disposal of this lamp may be regulated under applicable environmental laws due to presence of mercury. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance (www.eiae.org). For additional safety information about the lamp in this digital projector, please see: www.hp.com/hpinfo/globalcitizenship/environment/productdata • Because the lamp assembly operates at a very high temperature, wait 30 minutes before removing the lamp module. 1. Turn off the projector and allow it to cool for 30 minutes. 2. If the projector is installed in a ceiling mount, remove it from the mount. 3. Unplug the power cord. 40 Maintaining the Projector

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
Maintaining the Projector
40
Replacing the lamp module
As the projector operates over time, the brightness of the projector lamp gradually decreases
and the lamp becomes more susceptible to breakage. You can install a new lamp at any time
to bring the projector up to factory-fresh brightness. We recommend replacing the lamp if a
warning message is displayed.
WARNING!
Replacing the lamp module requires special consideration:
•
To reduce the risk of injury, be careful when removing the lamp module as broken glass
might be present. HP also recommends wearing goggles and gloves when removing the
lamp module. If the lamp is broken, contact HP about repairs that might be required due to
glass fragments.
•
The lamp in this digital projector contains mercury. If the lamp breaks, adequately ventilate
the immediate area, discard any nearby food and drink, and thoroughly clean the table
surface around the projector. Wash your hands after cleaning the area or handling a
broken lamp. Note that disposal of this lamp may be regulated under applicable
environmental laws due to presence of mercury. For disposal or recycling information,
please contact your local authorities or the Electronic Industries Alliance (www.eiae.org).
For additional safety information about the lamp in this digital projector, please see:
www.hp.com/hpinfo/globalcitizenship/environment/productdata
•
Because the lamp assembly operates at a very high temperature, wait 30 minutes before
removing the lamp module.
1.
Turn off the projector and allow it to cool for 30 minutes.
2.
If the projector is installed in a ceiling mount, remove it from the mount.
3.
Unplug the power cord.