HP xp7030 User Guide - Page 55

Fixing Problems - red temperature light is blinking

Get HP xp7030 - Digital Projector PDF manuals and user guides View all HP xp7030 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

6 Fixing Problems Troubleshooting suggestions If you have a problem with your projector, check the following statement that most closely matches the nature of the problem, then look in that section of this chapter: • "Warning light problems" on page 55 • "Start-up problems" on page 56 • "Picture problems" on page 56 • "Sound problems" on page 59 • "Interruption problems" on page 59 • "Remote control problems" on page 60 TIP: If these suggestions do not solve your problem, go to http://www.hp.com/support for additional information. To contact HP, refer to the support guide included with the projector. Warning light problems If both red warning lights are blinking: • Allow the projector to cool down after it turns off. If this condition occurs after you restart the projector, an internal component has failed. Contact HP for assistance. If the red temperature light is on: • Allow the projector to cool down after it turns off. Be sure that nothing is near or blocking the vents on the projector, and that the vents are free of lint and other objects. Remove any sources of excess heat in the room. Observe temperature and altitude limits (see "Specifications" on page 61). If the warning light turns on or blinks after you restart the projector, contact HP for assistance. If the red temperature light is blinking: • Contact HP for assistance. Troubleshooting suggestions 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
Troubleshooting suggestions
55
6
Fixing Problems
Troubleshooting suggestions
If you have a problem with your projector, check the following statement that most closely
matches the nature of the problem, then look in that section of this chapter:
•
“Warning light problems” on page 55
•
“Start-up problems” on page 56
•
“Picture problems” on page 56
•
“Sound problems” on page 59
•
“Interruption problems” on page 59
•
“Remote control problems” on page 60
TIP:
If these suggestions do not solve your problem, go to http://www.hp.com/support for
additional information. To contact HP, refer to the support guide included with the projector.
Warning light problems
If both red warning lights are blinking:
•
Allow the projector to cool down after it turns off. If this condition occurs after you
restart the projector, an internal component has failed. Contact HP for assistance.
If the red temperature light is on:
•
Allow the projector to cool down after it turns off. Be sure that nothing is near or
blocking the vents on the projector, and that the vents are free of lint and other objects.
Remove any sources of excess heat in the room. Observe temperature and altitude limits
(see “Specifications” on page 61). If the warning light turns on or blinks after you
restart the projector, contact HP for assistance.
If the red temperature light is blinking:
•
Contact HP for assistance.