HP xp7030 User Guide - Page 53

Power and status functions, Setup functions continued

Get HP xp7030 - Digital Projector PDF manuals and user guides View all HP xp7030 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Setup functions (continued) Command Parameters Description FWVERS ? Queries the projector firmware model number and firmware version. Similar to VERS, but used to verify that a firmware update image is appropriate for the projector. The notification takes this form: *VERS="proj_model:M.mmm" IPADDR Hex IP address, ? Used by network module to tell projector the IP address to display in the help menu. SNET Hex subnet mask, ? Used by network module to tell projector the subnet mask to display in the help menu. MAC Hex MAC address, ? Used by network module to tell projector the MAC address to display in the help menu. SNUM ? Queries the projector's serial number. RSET None Restores all settings to defaults. Power and status functions Command Parameters SHDN None W or WAKE None Description Puts the projector into cool-down state, and later into standby state. The projector sends a notification when it enters cooldown state (STAT=3), and another when it enters standby state (STAT=0). This keyword requires the projector to be in its on state (STAT=1). Do not send any requests other than STAT in the time between the cool-down and standby state notifications. Otherwise, unexpected results can occur. Puts the projector into warm-up state, and later into on state. The projector sends a notification when it enters warm-up state (STAT=2), and another when it enters the on state (STAT=1). This keyword requires the projector to be in standby state (STAT=0). Do not send any requests other than STAT in the time between the warm-up and on state notifications. Otherwise, unexpected results can occur. Connecting to a room controller 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
Connecting to a room controller
53
FWVERS
?
Queries the projector firmware model number and firmware
version. Similar to VERS, but used to verify that a firmware
update image is appropriate for the projector. The
notification takes this form:
*VERS="proj_model:M.mmm"
IPADDR
Hex IP address
, ?
Used by network module to tell projector the IP address to
display in the help menu.
SNET
Hex subnet mask
, ?
Used by network module to tell projector the subnet mask to
display in the help menu.
MAC
Hex MAC address
, ?
Used by network module to tell projector the MAC address
to display in the help menu.
SNUM
?
Queries the projector's serial number.
RSET
None
Restores all settings to defaults.
Power and status functions
Command
Parameters
Description
SHDN
None
Puts the projector into cool-down state, and later into standby
state. The projector sends a notification when it enters cool-
down state (STAT=3), and another when it enters standby state
(STAT=0). This keyword requires the projector to be in its on
state (STAT=1).
Do not send any requests other than STAT in the time between
the cool-down and standby state notifications. Otherwise,
unexpected results can occur.
W or WAKE
None
Puts the projector into warm-up state, and later into on state.
The projector sends a notification when it enters warm-up state
(STAT=2), and another when it enters the on state (STAT=1).
This keyword requires the projector to be in standby state
(STAT=0).
Do not send any requests other than STAT in the time between
the warm-up and on state notifications. Otherwise, unexpected
results can occur.
Setup functions (continued)
Command
Parameters
Description