HP xp7030 User Guide - Page 56

Start-up problems, Picture problems - manual

Get HP xp7030 - Digital Projector PDF manuals and user guides View all HP xp7030 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

If the red lamp light is on: • Install a new lamp. If the lamp light is on after you install a new lamp module, remove and reinstall the lamp module. If a new lamp does not fix the problem, contact HP for assistance. If the red lamp light is blinking: • Contact HP for assistance. If the red lamp light is flickering quickly: • Check that the cover over the lamp at the side of the projector is correctly installed and fully attached. Check the tab at the top of the cover and latch at the bottom. Start-up problems If no lights or sounds turn on: • Be sure that the power cable is securely connected to the projector and the other end is plugged into an outlet with power. • Be sure the disconnect switch is turned on. • Press the power button again. • Unplug the power cord for 15 seconds, then plug it in and press the power button again. Picture problems If a "scanning" or "waiting" message is displayed on a blank screen: • Press the source button on the projector or remote control one or more times until the correct source name is selected. • Be sure the external source is turned on and connected. • For a computer connection, ensure your notebook computer's external video port is turned on. Refer to the computer manual. On some notebooks, for example, press the FN+F4 or FN+F5 function keys to turn on the external video port. If the wrong input source is displayed: • Press the source button on the projector or the remote control one or more times to select another active input source. 56 Fixing Problems

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
Fixing Problems
56
If the red lamp light is on:
•
Install a new lamp. If the lamp light is on after you install a new lamp module, remove
and reinstall the lamp module. If a new lamp does not fix the problem, contact HP for
assistance.
If the red lamp light is blinking:
•
Contact HP for assistance.
If the red lamp light is flickering quickly:
•
Check that the cover over the lamp at the side of the projector is correctly installed and
fully attached. Check the tab at the top of the cover and latch at the bottom.
Start-up problems
If no lights or sounds turn on:
•
Be sure that the power cable is securely connected to the projector and the other end is
plugged into an outlet with power.
•
Be sure the disconnect switch is turned on.
•
Press the power button again.
•
Unplug the power cord for 15 seconds, then plug it in and press the power button
again.
Picture problems
If a “scanning” or “waiting” message is displayed on a blank screen:
•
Press the
source
button on the projector or remote control one or more times until the
correct source name is selected.
•
Be sure the external source is turned on and connected.
•
For a computer connection, ensure your notebook computer’s external video port is
turned on. Refer to the computer manual. On some notebooks, for example, press the
F
N
+F4 or F
N
+F5 function keys to turn on the external video port.
If the wrong input source is displayed:
•
Press the
source
button on the projector or the remote control one or more times to select
another active input source.