Hikvision DS-KH6320-WTE1 Configuration Guide - Page 63

Network Camera Information, Add Camera, Export and Import Added Device Information, Steps

Get Hikvision DS-KH6320-WTE1 PDF manuals and user guides View all Hikvision DS-KH6320-WTE1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

Network Indoor Station Configuration Guide ● When the zone type is set to be 24H Alarm, the indoor station will receive alarm message when the detector is triggered no matter it is under arming mode or disarming mode. ● When the zone type is set to be Delay Alarm, only under arming mode, the indoor station will receive alarm message when the detector is triggered. Under disarming mode, it will not receive alarm message when the detector is triggered. ● After setting enter delay time, if OK is pressed within the enter delay time after the alarm, the alarm event will not be uploaded to the management center; if OK is not pressed within the enter delay time after the alarm, the alarm event will be uploaded to the management center. ● The exit delay is the time between you enable the arming mode and the arming takes effect. Network Camera Information You can add, delete and edit cameras that can be added to the video intercom products, with two ways of getting stream: direct or URL. By exporting and importing the added device information, you can edit added devices parameters in batch. Add Camera Steps 1. Click IP Camera Information to enter IP camera information page. Figure 4-12 IP Camera Information 2. Click Add to pop up the device adding dialog box. 3. Enter corresponding information (device name, IP address, port No., user name, password, etc.), and click OK. Note Indoor extension does not support this function. Export and Import Added Device Information Steps 1. Click Export to export the added device information file. 2. Edit parameters of added devices in batch in the exported file. 3. Click Import to pop up importing box, and open the edited added device information file. 54

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
●
When the zone type is set to be 24H Alarm, the indoor
sta°on
will receive alarm message
when the detector is triggered no
ma±er
it is under arming mode or disarming mode.
●
When the zone type is set to be Delay Alarm, only under arming mode, the indoor
sta°on
will
receive alarm message when the detector is triggered. Under disarming mode, it will not
receive alarm message when the detector is triggered.
●
Aſter
se²ng
enter delay
°me,
if OK is pressed within the enter delay
°me
aſter
the alarm, the
alarm event will not be uploaded to the management center; if OK is not pressed within the
enter delay
°me
aſter
the alarm, the alarm event will be uploaded to the management center.
●
The exit delay is the
°me
between you enable the arming mode and the arming takes
effect.
Network Camera
Informa°on
You can add, delete and edit cameras that can be added to the video intercom products, with two
ways of
ge²ng
stream: direct or URL. By
expor°ng
and
impor°ng
the added device
informa°on,
you can edit added devices parameters in batch.
Add Camera
Steps
1.
Click
IP Camera
Informa°on
to enter IP camera
informa°on
page.
Figure 4-12 IP Camera
Informa°on
2.
Click
Add
to pop up the device adding dialog box.
3.
Enter corresponding
informa°on
(device name, IP address, port No., user name, password, etc.),
and click
OK
.
Note
Indoor extension does not support this
func°on.
Export and Import Added Device
Informa°on
Steps
1.
Click
Export
to export the added device
informa°on
file.
2.
Edit parameters of added devices in batch in the exported
file.
3.
Click
Import
to pop up
impor°ng
box, and open the edited added device
informa°on
file.
Network Indoor
Sta°on
Configura°on
Guide
54