Husqvarna AUTOMOWER SOLAR HYBRID Operation Manual - Page 22

the like. The height must then be at least 15

Get Husqvarna AUTOMOWER SOLAR HYBRID PDF manuals and user guides View all Husqvarna AUTOMOWER SOLAR HYBRID manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

3. INSTALLATION Boundaries for the working area If a high obstacle, for example a wall or fence, borders the working area, the boundary wire should be laid 35 cm from the obstacle. This will prevent Automower® from colliding with the obstacle and reduce body wear. If the working area borders against a small ditch, for example, a flower bed or a small elevation, e.g. a low verge (3 - 5 cm), the boundary wire should be laid 30 cm inside the working area. This prevents the wheels from driving into the ditch or up onto the verge. If the working area borders against a flat path or the like that lies level with the lawn, it is possible to allow Automower® to run a little over the path. The boundary wire should then be laid 10 cm from the edge of the path. 35 cm 30cm When the working area is divided by a flat slab path that is level with the lawn, it is possible to allow Automower® to run over the path. It can be an advantage to lay the boundary wire under the slabs. The boundary wire can also be laid in the joint between the slabs. Note! Automower® must never run over a gravel path or similar material, which can damage the blades. IMPORTANT INFORMATION If the working area is adjacent to water bodies, slopes or precipices, the boundary wire should be supplemented with a fence or the like. The height must then be at least 15 cm. This will prevent Automower® from ending up outside the working area under any circumstances. 10 cm English - 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
English - 23
3. INSTALLATION
Boundaries for the working area
If a high obstacle, for example a wall or fence,
borders the working area, the boundary wire should
be laid 35 cm from the obstacle. This will prevent
Automower
®
from colliding with the obstacle and
reduce body wear.
If the working area borders against a small ditch, for
example, a flower bed or a small elevation, e.g. a low
verge (3 - 5 cm), the boundary wire should be laid
30 cm inside the working area. This prevents the
wheels from driving into the ditch or up onto the
verge.
If the working area borders against a flat path or the
like that lies level with the lawn, it is possible to allow
Automower
®
to run a little over the path. The
boundary wire should then be laid 10 cm from the
edge of the path.
When the working area is divided by a flat slab path
that is level with the lawn, it is possible to allow
Automower
®
to run over the path. It can be an
advantage to lay the boundary wire under the slabs.
The boundary wire can also be laid in the joint
between the slabs.
Note!
Automower
®
must never run over a gravel path
or similar material, which can damage the blades.
IMPORTANT INFORMATION
If the working area is adjacent to water
bodies, slopes or precipices, the boundary
wire should be supplemented with a fence or
the like. The height must then be at least 15
cm. This will prevent Automower
®
from
ending up outside the working area under
any circumstances.
35 cm
30
cm
10
cm