IBM 306m User Guide - Page 34

Installing, drive, simple-swap, Serial

Get IBM 306m - eServer xSeries - 8849 PDF manuals and user guides
UPC - 000435867605
View all IBM 306m manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

the assembly. Make sure that the riser-card assembly is fully seated in the riser-card connectors on the system board. If you have other options to install or remove, do so now. Otherwise, go to "Completing the installation" on page 30. Installing a hard disk drive Locate the documentation that comes with the hard disk drive and follow those instructions in addition to the instructions in this chapter. Attention: To avoid damage to the hard disk drive connectors, make sure that the cover is in place and fully closed whenever you install or remove a hard disk drive. Installing a simple-swap Serial ATA hard disk drive Attention: Simple-swap hard disk drives are not hot-swappable. Disconnect all power from the server before removing or installing a simple-swap hard disk drive. To install a simple-swap Serial ATA hard disk drive, complete the following steps. Note: If you have only one hard disk drive, install it in the left drive bay. Attention: To avoid damage to the hard disk drive connectors, make sure that the cover is in place and fully closed whenever you install or remove a hard disk drive. 1. Read the safety information that begins on page v and "Installation guidelines" on page 17. 2. Make sure that the server cover is in place and fully closed. 3. Turn off the server and peripheral devices, and disconnect the power cord and all external cables. 4. Remove the filler panel from the bay. 5. Pull the loops of the drive tray toward each other, and slide the drive into the server until the drive connects to the back panel. 6. Release the loops of the drive tray. 7. Insert the filler panel into the bay to cover the drive. 22 IBM xSeries 306m Types 8849 and 8491: User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
the
assembly.
Make
sure
that
the
riser-card
assembly
is
fully
seated
in
the
riser-card
connectors
on
the
system
board.
If
you
have
other
options
to
install
or
remove,
do
so
now.
Otherwise,
go
to
“Completing
the
installation”
on
page
30.
Installing
a
hard
disk
drive
Locate
the
documentation
that
comes
with
the
hard
disk
drive
and
follow
those
instructions
in
addition
to
the
instructions
in
this
chapter.
Attention:
To
avoid
damage
to
the
hard
disk
drive
connectors,
make
sure
that
the
cover
is
in
place
and
fully
closed
whenever
you
install
or
remove
a
hard
disk
drive.
Installing
a
simple-swap
Serial
ATA
hard
disk
drive
Attention:
Simple-swap
hard
disk
drives
are
not
hot-swappable.
Disconnect
all
power
from
the
server
before
removing
or
installing
a
simple-swap
hard
disk
drive.
To
install
a
simple-swap
Serial
ATA
hard
disk
drive,
complete
the
following
steps.
Note:
If
you
have
only
one
hard
disk
drive,
install
it
in
the
left
drive
bay.
Attention:
To
avoid
damage
to
the
hard
disk
drive
connectors,
make
sure
that
the
cover
is
in
place
and
fully
closed
whenever
you
install
or
remove
a
hard
disk
drive.
1.
Read
the
safety
information
that
begins
on
page
v
and
“Installation
guidelines”
on
page
17.
2.
Make
sure
that
the
server
cover
is
in
place
and
fully
closed.
3.
Turn
off
the
server
and
peripheral
devices,
and
disconnect
the
power
cord
and
all
external
cables.
4.
Remove
the
filler
panel
from
the
bay.
5.
Pull
the
loops
of
the
drive
tray
toward
each
other,
and
slide
the
drive
into
the
server
until
the
drive
connects
to
the
back
panel.
6.
Release
the
loops
of
the
drive
tray.
7.
Insert
the
filler
panel
into
the
bay
to
cover
the
drive.
22
IBM
xSeries
306m
Types
8849
and
8491:
User’s
Guide