Home » Icom Manuals » Two-Way Radios » Icom IC-2730A » Manual Viewer

Icom IC-2730A Instruction Manual - Page 41

SCAN OPERATION, ■ About the scan function, ◇ VFO scan, ◇ Memory scan

Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

5 SCAN OPERATION ■■About the scan function DDVFO scan (p. 41) • ALL (Full scan) Repeatedly scans the entire band. 118 MHz 550 MHz P SKIP Scan P SKIP Jump • BAND (Selected band scan) S cans all frequencies over the entire selected band. Band edge Band edge P SKIP Scan P SKIP Jump • PROG 0~24 (Program scan) S cans the program scan edge range. Band Lower edge freq. Scan edges Higher Band freq. edge Jump Scan Jump • P-LINK0~9 (Program link scan) S equentially scans the program scan edge ranges which are set to link in the "P-LINK" (Program Link) item of the EXMENU mode. (p. 14) For your reference: The frequencies that are set as "PSKIP" are not scanned. (p. 13) NOTE: At least one program scan edge range must be programmed to start a program scan. (p. 38) SCAN OPERATION DDMemory scan (p. 43) • ALL (Full memory scan) Scans all Memory channels. • BAND (Selected band memory scan) Scans all Memory channels in the same frequency band as the selected channel. 5 • MODE (Mode memory scan) Scans Memory channels that are programmed with the same receiving mode as the currently selected mode. DDMemory bank scan (p. 43) • ALL (Full bank scan) Scans all banks. • B-LINK (Bank link scan) Sequentially scans the banks that are set to link in the "B-LINK" (Bank Link) item of the EXMENU mode. • BANK-A~J (Bank scan) Scans the Memory channels in the selected bank. For your reference: The frequencies that are set as "PSKIP" or "SKIP" are not scanned. (p. 44) NOTE: Two or more memory channels must be programmed to start a Memory scan. 36

Section	Page
Front cover	1
FOREWORD	2
EXPLICIT DEFINITIONS	2
IMPORTANT	2
SUPPLIED ACCESSORIES	2
PRECAUTIONS	3
TABLE OF CONTENTS	5
1 PANEL DESCRIPTION	6
■ Controller — Front panel	6
■ Controller — Display	7
■ Main unit	10
■ About the HM-207 microphone	11
2 MENU MODE	14
■ MENU mode screen	14
■ MENU mode construction	14
■ Selecting the MENU item	16
■ Setting items	17
◇ MENU mode	17
◇ EXMENU mode	17
■ MENU items	23
3 BASIC OPERATION	28
■ Selecting the MAIN band	28
■ Selecting the Mode	28
◇ VFO mode	28
◇ Memory mode	28
◇ Call channel mode	28
◇ Weather channel mode	28
■ Selecting the operating band	29
■ Setting a frequency	29
◇ Selecting a tuning step	30
■ Setting audio volume andsquelch level	30
■ Lock function	30
■ Transmitting	31
■ Selecting the operating mode	31
■ Audio mute function	32
■ Monitor function	32
■ Setting the microphone gain level	32
4 MEMORY OPERATION	33
■ General description	33
◇ The number of the Memory channel	33
◇ Memory channel content	33
■ Selecting a Memory or Call channel	34
◇ Selecting a Memory channel	34
◇ Selecting a Call channel	34
■ Writing into a Memory or Call channel	35
◇ Writing into the selected channel	35
◇ Writing into a blank channel	35
◇ Copying Memory content to the VFO	36
◇ Copying Memory content to another Memory channel	36
■ Setting a Memory bank	37
◇ Assigning a Memory channel to a Memory bank	37
◇ Directly entering into a Memory bank	38
◇ Selecting the Memory bank mode	38
■ Entering a Memory or Bank name	39
■ Clearing a Memory channel	40
5 SCAN OPERATION	41
■ About the scan function	41
◇ VFO scan	41
◇ Memory scan	41
◇ Memory bank scan	41
◇ [DIAL] operation during a scan	42
◇ Tuning step for a VFO scan	42
◇ Skip function	42
◇ Scan Stop Beep function	42
◇ Receive mode during a scan	43
◇ When a signal is received	43
◇ Scan name	43
■ Entering scan edges	43
■ VFO mode scan	46
◇ VFO mode scan	46
■ Setting and clearing the skip frequencies	47
◇ Setting the skip frequencies	47
◇ Clearing the skip frequencies	47
■ Memory scan	48
◇ Memory (skip) scan	48
◇ Memory bank scan	48
■ Setting and clearing skipchannels	49
■ Setting the temporary skipfunction	49
6 PRIORITY WATCH	50
■ Priority watch	50
◇ VFO and a Priority channel	50
◇ VFO and a Memory/Bank scan	50
■ VFO and a Priority channel	51
◇ VFO frequency and a Priority channel	51
◇ VFO scan and a Priority channel	51
■ VFO and a Memory/Bank scan	52
◇ VFO frequency and a Memory/Bank scan	52
◇ VFO scan and a Memory/Bank scan	52
7 REPEATER AND DUPLEX OPERATIONS	53
■ Repeater operation	53
◇ Checking the repeater input signal	54
◇ 1750 Hz tone burst	54
■ Duplex operation	55
◇ Setting the frequency offset	55
◇ Setting the duplex direction	55
◇ Duplex operation	56
■ Off band indication	56
■ Auto repeater function	57
◇ Frequency range and offset direction	57
8 OTHER FUNCTIONS	58
■ Home Channel Beep function	58
◇ Setting the Home channel	58
◇ Home channel operation	58
■ Using the DTMF Memory	59
◇ Entering a DTMF code	59
■ Transmitting DTMF code	60
◇ Transmitting DTMF code (DTMF Memory)	60
◇ Transmitting DTMF code (Direct Input)	60
◇ Selecting the DTMF transmit speed	61
■ Tone Squelch function	61
◇ Operation	61
◇ Setting the Tone frequency	63
◇ Setting the Repeater Tone frequency	63
◇ Setting the DTCS code	64
◇ Setting the DTCS polarity	64
■ Weather channel operation(USA version only)	65
◇ Weather channel selection	65
◇ Weather alert function	65
■ Cloning function	66
◇ Cloning from a PC using a cloning cable	66
◇ Cloning between transceivers	66
9 INSTALLATION AND CONNECTIONS	68
■ Connecting the controller tothe main unit	68
◇ When using the MBA-4 combination bracket	68
■ Connecting a microphone	68
■ Connecting to a DC power supply	69
■ Installing the controller	69
◇ When installing into your vehicle	69
◇ Attaching to a flat surface	70
■ Installing in a vehicle	71
◇ Using the mounting bracket	71
■ Installing an antenna	72
◇ About Coaxial cable	72
◇ About the internal duplexer	72
■ Connecting to a battery	73
10 OPTIONS	75
11 Bluetooth® OPERATION	76
■ Operating Bluetooth®	76
■ Electromagnetic Interference	76
■ Installing the UT-133	77
■ Pairing with a headset	78
■ VOX function	79
◇ Using the VOX function	79
◇ Setting the VOX level	79
◇ VOX-related settings	80
■ Other headset settings	80
◇ AF Output	80
◇ About the VS-3 headset	81
■ The maximum number ofpaired devices	82
■ Disconnecting from aBluetooth® device	82
■ Deleting a Bluetooth® devicefrom the pairing list	82
■ Resetting the installedBluetooth® unit	83
12 SPECIFICATIONS	84
◇ General	84
◇ Transmitter	85
◇ Receiver	85
13 MAINTENANCE	86
■ Resetting	86
◇ Partial Reset	86
◇ All Reset	86
■ Power protect function	87
■ Spurious signals	87
■ Fuse replacement	87
■ Troubleshooting	88
14 Information	90
Index	91

Match case Limit results 1 per page

SCAN OPERATION

■

About the scan function

VFO scan

(p. 41)

•

ALL

(Full scan)

Repeatedly scans the entire band.

118 MHz

550 MHz

Scan

P SKIP

Jump

•

BAND

(Selected band scan)

Scans all frequencies over the entire selected band.

Band edge

Scan

P SKIP

Jump

•

PROG 0

(Program scan)

Scans the program scan edge range.

Band

edge

Lower

freq.

Higher

freq.

Band

edge

Scan edges

Scan

Jump

•

P-LINK0

(Program link scan)

Sequentially scans the program scan edge ranges which

are set to link in the “P-LINK” (Program Link) item of the

EXMENU mode. (p. 14)

For your reference:

The frequencies that are set as

“PSKIP” are not scanned. (p. 13)

NOTE:

At least one program scan edge range must be

programmed to start a program scan. (p. 38)

Memory scan

(p. 43)

•

ALL

(Full memory scan)

Scans all Memory channels.

•

BAND

(Selected band memory scan)

Scans all Memory channels in the same frequency band as

the selected channel.

•

MODE

(Mode memory scan)

Scans Memory channels that are programmed with the

same receiving mode as the currently selected mode.

Memory bank scan

(p. 43)

•

ALL

(Full bank scan)

Scans all banks.

•

B-LINK

(Bank link scan)

Sequentially scans the banks that are set to link in the

“B-LINK” (Bank Link) item of the EXMENU mode.

•

BANK-A

(Bank scan)

Scans the Memory channels in the selected bank.

For your reference:

The frequencies that are set as

“PSKIP” or “SKIP” are not scanned. (p. 44)

NOTE:

Two or more memory channels must be pro-

grammed to start a Memory scan.