Icom MR-1220 Instruction Manual - Page 57

Installing the UX-234 Video output unit, WARNING, CAUTION: DO

Get Icom MR-1220 PDF manuals and user guides View all Icom MR-1220 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

9 Installation and connections IInnsstatlalinlglitnhge UtXh-e23U4 XVid-2eo34ouVtpuidt uenoit output unit You can connect an external display or a PC monitor with a VGA connector to the display unit by installing an 1 optional UX-234 video output unit. The external monitor requires the resolution of 800 × 600 or higher. 2 RRWARNING! Disconnect the power cable from the display unit, before installing the optional unit. 1. Place the display unit facing the front panel down on a flat and horizontal place. 2. Remove the cable hole seal to the left of the serial number label. CAUTION: DO NOT use your finger nail to remove the seal. Otherwise, you may injure your nail. 3. Remove the 12 screws from the rear panel of the display unit. 4. Slowly open the rear case and disconnect the 5 connectors from the display unit's main board. LLThe one connector is lock-type. Hold the release on connector head to disconnect the connector. CAUTION: DO NOT pull the cables when opening the rear case. This could damage the cables and/or display unit. Hole seal 3 Screw 4 5 6 7 8 9 10 11 12 5. Pass the video output cable though the sealing 13 nut, sealing tube, washer, and the hole on the rear panel, and then screw in and tighten the sealing 14 tube. Sealing nut Washer Sealing 15 tube 16 17 18 19 20 21 6. Connect the video output cable to the connector on the UX-234. Video output cable UX-234 52

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
52
INSTALLATION AND CONNECTIONS
9
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Installing the UX-234 Video output unit
Installing the UX-234 Video output unit
You can connect an external display or a PC monitor with a VGA connector to the display unit by installing an
optional UX-234
VIDEO
OUTPUT
UNIT
.
The external monitor requires the resolution of 800 × 600 or higher.
R
WARNING!
Disconnect the power cable from the
display unit, before installing the optional unit.
1.
Place the display unit facing the front panel down
on a flat and horizontal place.
2.
Remove the cable hole seal to the left of the serial
number label.
CAUTION: DO NOT
use your finger nail to
remove the seal. Otherwise, you may injure your
nail.
3.
Remove the 12 screws from the rear panel of the
display unit.
4.
Slowly open the rear case and disconnect the 5
connectors from the display unit’s main board.
L
The one connector is lock-type. Hold the release on
connector head to disconnect the connector.
CAUTION: DO NOT
pull the cables when
opening the rear case. This could damage the
cables and/or display unit.
5.
Pass the video output cable though the sealing
nut, sealing tube, washer, and the hole on the rear
panel, and then screw in and tighten the sealing
tube.
6.
Connect the video output cable to the connector
on the UX-234.
Sealing nut
Hole seal
Screw
Video output cable
UX-234
Sealing
tube
Washer