Icom MR-1220 Instruction Manual - Page 58

CAUTION: DO NOT, pinch the cables when

Get Icom MR-1220 PDF manuals and user guides View all Icom MR-1220 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

9 Installation and connections Installing the UX-234 Video output unit 7. Connect the UX-234 to the display unit's connector, then adjust the 4 screw holes. 8. Fix the UX-234 to the display unit tightening the 4 screws supplied with the UX-234. Screw UX-234 Connector Connector 9. Secure the video output cable to the UX-234 using a cable tie. 10. Tightly secure the ferrite EMI filter around the video output cable near the UX-234. 11. Reconnect the four connectors to the display unit's main board. Cable tie Ferrite EMI filter 12. Replace the gasket, rear case, and screws to their original position. LLMake sure the gasket is properly seated. CAUTION: DO NOT pinch the cables when closing the rear case. This could damage the cables. 13. Adjust the video output cable length and then tighten the sealing nut. Sealing nut Sealing tube Video output cable To an external display 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
53
9
INSTALLATION AND CONNECTIONS
Installing the UX-234 Video output unit
7.
Connect the UX-234 to the display unit’s
connector, then adjust the 4 screw holes.
8.
Fix the UX-234 to the display unit tightening the 4
screws supplied with the UX-234.
9.
Secure the video output cable to the UX-234
using a cable tie.
10.
Tightly secure the ferrite EMI filter around the
video output cable near the UX-234.
11. Reconnect the four connectors to the display unit’s
main board.
12. Replace the gasket, rear case, and screws to their
original position.
L
Make sure the gasket is properly seated.
CAUTION: DO NOT
pinch the cables when
closing the rear case. This could damage the
cables.
13. Adjust the video output cable length and then
tighten the sealing nut.
UX-234
Connector
Connector
Screw
Ferrite EMI filter
Cable tie
Sealing nut
Sealing
tube
Video output
cable
To an external display