Intel D865GLC Manual - Page 92

Recovering the BIOS

Get Intel D865GLC - Desktop Board Motherboard PDF manuals and user guides
UPC - 683728198374
View all Intel D865GLC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 92 highlights

5. When the utility asks for confirmation that you want to flash the new BIOS into memory, select continue with Programming. Press . 6. When the utility displays the message upgrade is complete, remove the floppy disk. Press . 7. As the computer boots, check the BIOS identifier (version number) to make sure the upgrade was successful. 8. To enter the Setup program, press when you see the message: Press Key if you want to run SETUP 9. For proper operation, load the Setup program defaults. To load the defaults, press . 10. To accept the defaults, press . 11. Set the options in the Setup program to the settings you wrote down before the BIOS upgrade. 12. To save the settings, press . 13. To accept the settings, press . 14. Turn off the computer and reboot. Recovering the BIOS It is unlikely that anything will interrupt the BIOS upgrade, however, if an interruption occurs, the BIOS could be damaged. The following steps explain how to recover the BIOS if an upgrade fails. The following procedure uses the recovery mode for the Setup program. See Chapter 3 for more information about Setup modes. Note: Because of the small amount of code available in the non-erasable boot block area, there is no video support. You will not see anything on the screen during the procedure. Monitor the procedure by listening to the speaker and looking at the floppy drive LED. 1. Turn off all peripheral devices connected to the computer. Turn off the computer. 2. Remove the computer cover. 3. Locate the configuration header (Jumper J9J4 on the motherboard). 4. On the header (J9J4), remove the jumper from all pins as shown below to set recovery mode for Setup. 1 2 3 Configuration Jumper J9J4 D865GLC Motherboard Manual 91

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
D865GLC Motherboard Manual
91
5. When the utility asks for confirmation that you want to flash the new BIOS into
memory, select continue with Programming.
Press <Enter>.
6. When the utility displays the message upgrade is complete, remove the floppy
disk.
Press <Enter>.
7. As the computer boots, check the BIOS identifier (version number) to make sure
the upgrade was successful.
8. To enter the Setup program, press
<F2> when you see the message:
Press <F2> Key if you want to run SETUP
9. For proper operation, load the Setup program defaults.
To load the defaults,
press <F9>.
10. To accept the defaults, press <Enter>.
11. Set the options in the Setup program to the settings you wrote down before the
BIOS upgrade.
12. To save the settings, press <F10>.
13. To accept the settings, press <Enter>.
14. Turn off the computer and reboot.
Recovering the BIOS
It is unlikely that anything will interrupt the BIOS upgrade, however, if an interruption
occurs, the BIOS could be damaged.
The following steps explain how to recover the
BIOS if an upgrade fails.
The following procedure uses the recovery mode for the
Setup program.
See Chapter 3 for more information about Setup modes.
Note:
Because of the small amount of code available in the non-erasable boot block
area, there is no video support.
You will not see anything on the screen during the
procedure.
Monitor the procedure by listening to the speaker and looking at the
floppy drive LED.
1. Turn off all peripheral devices connected to the computer.
Turn off the computer.
2. Remove the computer cover.
3. Locate the configuration header (Jumper J9J4 on the motherboard).
4. On the header (J9J4), remove the jumper from all pins as shown below to set
recovery mode for Setup.
Configuration Jumper
J9J4
1
2
3