Intermec PB22 PB22 and PB32 Mobile Label and Receipt Printer User Guide - Page 49

Configuring the PB22 and PB32, PB22 and PB32 Mobile Label and Receipt Printer User Guide

Get Intermec PB22 PDF manuals and user guides View all Intermec PB22 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

Chapter 2 - Configuring the PB22 and PB32 3 From the host PC, check the wireless settings. If you have an IPL version of the printer, send these commands to the printer: wt,SSID wt,WEP1 wt,WEP2 wt,WEP3 wt,WEP4 wt,AUTH wt,WPA wt,WPA2 wt,WPA_PSK wt,ROAM wt,PWR_MODE wt,CHANNEL wt,AP_MAC wt,SIGNAL wt,SPEED wt,ACTIVE If you have a Fingerprint version of the printer, send this command to the printer: setup write "wlan","uart1:" 4 Set up the printer to use the correct SSID and authentication modes. See one of these procedures to configure wireless printing on your IPL or Fingerprint printer. 5 If you are going to use certificates for validation, transfer the certificate to the printer. The printer can accept .pfx, .pem, and .der certificates. 6 Verify that the printer is connected to the access point and make sure it has an IP address allocated to it. PB22 and PB32 Mobile Label and Receipt Printer User Guide 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
Chapter 2 — Configuring the PB22 and PB32
PB22 and PB32 Mobile Label and Receipt Printer User Guide
37
3
From the host PC, check the wireless settings.
If you have an IPL version of the printer, send these commands to
the printer:
<STX><SI>wt,SSID<ETX>
<STX><SI>wt,WEP1<ETX>
<STX><SI>wt,WEP2<ETX>
<STX><SI>wt,WEP3<ETX>
<STX><SI>wt,WEP4<ETX>
<STX><SI>wt,AUTH<ETX>
<STX><SI>wt,WPA<ETX>
<STX><SI>wt,WPA2<ETX>
<STX><SI>wt,WPA_PSK<ETX>
<STX><SI>wt,ROAM<ETX>
<STX><SI>wt,PWR_MODE<ETX>
<STX><SI>wt,CHANNEL<ETX>
<STX><SI>wt,AP_MAC<ETX>
<STX><SI>wt,SIGNAL<ETX>
<STX><SI>wt,SPEED<ETX>
<STX><SI>wt,ACTIVE<ETX>
If you have a Fingerprint version of the printer, send this
command to the printer:
setup write "wlan","uart1:"
4
Set up the printer to use the correct SSID and authentication
modes. See one of these procedures to configure wireless printing
on your IPL or Fingerprint printer.
5
If you are going to use certificates for validation, transfer the
certificate to the printer. The printer can accept .pfx, .pem, and
.der certificates.
6
Verify that the printer is connected to the access point and make
sure it has an IP address allocated to it.