Intermec SF51 SF51 Cordless Scanner User's Guide - Page 16

Charging the Battery, Checking the Battery Status

Get Intermec SF51 PDF manuals and user guides View all Intermec SF51 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Chapter 1 - Learning About the SF51 The lithium-ion battery pack that is used in this device may present a fire or chemical burn hazard if it is mistreated. Do not disassemble it, heat it above 100°C (212°F) or incinerate it. Charging the Battery Make sure you fully charge the battery before you start using the SF51. To charge the battery • Place the SF51 in the 1-bay charger (Model 074645) or the 4-bay charger (Model 074646). A fully discharged battery charges to 100% capacity in approximately 3 hours. It may take longer than 3 hours to charge the battery if the temperature is near the minimum (0°C, 32°F) or maximum (35°C, 95°F) charging temperature. Note: When you place the SF51 in the 1-bay or 4-bay charger, you reset the SF51 scanner control firmware. For more information, see "Resetting the SF51" on page 31. Checking the Battery Status • Press the Scan button. If the status light on the SF51 turns red, the battery is low (less than 20% battery capacity remaining). You need to charge the battery now. SF51 Cordless Scanner User's Guide 3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
Chapter 1 — Learning About the SF51
SF51 Cordless Scanner User’s Guide
3
Charging the Battery
Make sure you fully charge the battery before you start using the
SF51.
To charge the battery
•
Place the SF51 in the 1-bay charger (Model 074645) or the
4-bay charger (Model 074646). A fully discharged battery
charges to 100% capacity in approximately 3 hours.
It may take longer than 3 hours to charge the battery if the
temperature is near the minimum (0°C, 32°F) or maximum
(35°C, 95°F) charging temperature.
Checking the Battery Status
•
Press the
Scan
button.
If the status light on the SF51 turns red, the battery is low
(less than 20% battery capacity remaining). You need to
charge the battery now.
The lithium-ion battery pack that is used in this device may
present a fire or chemical burn hazard if it is mistreated. Do
not disassemble it, heat it above 100°C (212°F) or incinerate
it.
Note:
When you place the SF51 in the 1-bay or 4-bay charger,
you reset the SF51 scanner control firmware. For more
information, see
“Resetting the SF51” on page 31
.