JVC GR-DV3000U Instructions - Page 68

68 EN USING THE REMOTE CONTROL UNIT (cont.) Program IN OUT MODE 1-- -- : -- ~ 2 ~ 3 ~ 4 ~ 5 ~ 6 ~ 7 ~ 8 ~ T I ME CODE - - : - - TOTAL 00 : 00 Random Assemble Editing Menu Remote sensor FADE/WIPE EFFECT EDIT IN/OUT CANCEL PLAY R.A.EDIT ON/OFF Fader And Wipe Menu (available only for Random Assemble Editing) You can also use the fade/wipe effects on page 37. DISSOLVE The new scene gradually appears as the old one gradually disappears. WIPE - CORNER The new scene wipes in over the previous one from the upper right corner to the lower left corner. WIPE - WINDOW The next scene gradually wipes in from the center of the screen toward the corners, covering the previous scene. WIPE - SLIDE The next scene gradually wipes in over the previous one from right to left. WIPE - DOOR The previous scene wipes out from the center to the right and left, like a door being pushed open to reveal the next scene. WIPE - SCROLL The new scene wipes in over the last one from the bottom of the screen to the top. WIPE - SHUTTER The new scene wipes in over the previous one from the center toward the top and bottom of the screen. SELECT SCENES 4 Point the remote control at the camcorder's remote sensor. Press PLAY (4) and then press R.A.EDIT ON/OFF on the remote control. The Random Assemble Editing Menu appears. 5 If using a Fade/Wipe at the beginning of the scene, press FADE/WIPE on the remote control. • Cycle through the effects by pressing repeatedly, and stop when the one you want is displayed. • You cannot use a Picture Wipe/Dissolve at the beginning of Program 1. 6 At the beginning of the scene, press EDIT IN/ OUT on the remote control. The Edit-In position appears in the Random Assemble Editing Menu. 7 At the end of the scene, press EDIT IN/OUT. The Edit-Out position appears in the Random Assemble Editing Menu. 8 If using a Fade/Wipe at the end of the scene, press FADE/WIPE. • Cycle through the effects by pressing repeatedly, and stop when the one you want is displayed. • If you select a Fade/Wipe effect for an Edit-Out point, the effect is automatically applied to the following Edit-In point. • You cannot use a Picture Wipe/Dissolve at the end of the last scene. • When you use Fade/Wipe effects, that time is included in the total time (this does not apply to Picture Wipe/Dissolve). 9 If using Playback Special Effects, press EFFECT (੬ pg. 65). 10 Repeat steps 6 through 9 to register additional scenes. • To change previously registered points, press CANCEL on the remote control. The registered points disappear, one at a time, from the most recently registered point. • If you are not using Fade/Wipe or Program AE with special effects, repeat steps 6 and 7 only. NOTES: ● When choosing a scene, set Edit-In and Edit-Out points so that there is a relatively large difference between them. ● If the search time for an in-point exceeds 5 minutes, the recording deck's Record-Standby mode will be canceled and editing will not take place. ● If there are blank portions before or after the Edit-In and Edit-Out points, a blue screen may be included in the edited version. ● Since time codes register time only as accurately as seconds, the time code total time may not match the total program time exactly. ● Turning off the camcorder's power erases all registered EditIn and Edit-Out points. ● If you select Sepia or Monotone mode from Program AE with special effects, you cannot use the Dissolve or Black & White Fader. In this case the Dissolve or Black & White indicator begins blinking. Once the next Edit-In point is registered, the effect is turned off. To combine these effects, use Sepia or Monotone during recording, then use the Dissolve or Black & White Fader during Random Assemble Editing. ● It is not possible to use Fade/Wipe effects and Program AE with special effects during Random Assemble Editing using a DV cable.