Kenwood TK-862HG Operation Manual - Page 9

Installing The Transceiver

Get Kenwood TK-862HG PDF manuals and user guides View all Kenwood TK-862HG manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

INSTALLING THE TRANSCEIVER FOR PASSENGER SAFETY, INSTALL THE TRANSCEIVER SECURELY, USING THE SUPPLIED MOUNTING BRACKET, SO THE TRANSCEIVER WILL NOT BREAK LOOSE IN THE EVENT OF A COLLISION. 1 Mark the position of the holes in the dash, using the mounting bracket as a template. Drill the holes, then attach the mounting bracket using the 4 supplied 5 x 16 mm screws, the spring washers, and the flat washers. • Be sure to mount the transceiver in a location where the controls are within easy reach of the user, and where there is sufficient space at the rear of the transceiver for cable connections. 2 Connect the antenna and the supplied power cable to the transceiver. 3 Slide the transceiver into the mounting bracket and secure it using the 4 supplied hex-headed screws. 4 Mount the microphone hanger, using the 3 supplied 4 x 16 mm screws, in a location where it will be within easy reach of the user. • The microphone and microphone cable should be mounted in a place where they will not interfere with the safe operation of the vehicle. 5 Connect the optional microphone to the microphone jack on the front panel of the transceiver. Place the microphone on the hanger. WHEN REPLACING THE FUSE IN THE DC POWER CABLE, BE SURE TO REPLACE IT WITH A FUSE OF THE SAME VALUE. NEVER REPLACE A FUSE WITH A FUSE THAT HAS A HIGHER VALUE. Flat washer Spring washer 4 x 16 mm self-tapping screw Microphone hanger Power input connector Optional KMC-30 speaker/ microphone 5 x 16 mm self-tapping screw DC power cable Mounting bracket Antenna connector Hex-headed screw 12 V vehicle battery * The above diagram shows the M market transceiver. The antenna connector of the E market transceiver is different. A market code (M or E) can be found on the label attached to the package box. 3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
3
INSTALLING THE TRANSCEIVER
FOR PASSENGER SAFETY, INSTALL THE TRANSCEIVER SECURELY, USING THE
SUPPLIED MOUNTING BRACKET, SO THE TRANSCEIVER WILL NOT BREAK LOOSE IN
THE EVENT OF A COLLISION.
1
Mark the position of the holes in the dash, using the mounting bracket as a
template.
Drill the holes, then attach the mounting bracket using the 4
supplied 5 x 16 mm screws, the spring washers, and the flat washers.
•
Be sure to mount the transceiver in a location where the controls are within easy reach
of the user, and where there is sufficient space at the rear of the transceiver for cable
connections.
2
Connect the antenna and the supplied power cable to the transceiver.
3
Slide the transceiver into the mounting bracket and secure it using the 4
supplied hex-headed screws.
4
Mount the microphone hanger, using the 3 supplied 4 x 16 mm screws, in a
location where it will be within easy reach of the user.
•
The microphone and microphone cable should be mounted in a place where they will
not interfere with the safe operation of the vehicle.
5
Connect the optional microphone to the microphone jack on the front panel of
the transceiver.
Place the microphone on the hanger.
WHEN REPLACING THE FUSE IN THE DC POWER CABLE, BE SURE TO REPLACE IT
WITH A FUSE OF THE SAME VALUE.
NEVER
REPLACE A FUSE WITH A FUSE THAT HAS
A HIGHER VALUE.
Hex-headed screw
Microphone hanger
DC power cable
Mounting bracket
5 x 16 mm
self-tapping screw
4 x 16 mm self-tapping screw
Spring washer
Flat washer
Antenna
connector
Power input connector
12 V vehicle
battery
*
The above diagram shows the M market transceiver.
The antenna connector of the E market
transceiver is different.
A market code (M or E) can be found on the label attached to the package box.
Optional KMC-30
speaker/ microphone