Konica Minolta C83hc High Chroma GBC PUNCH G2 User Manual - Page 12

PUNCH G2 EN PUNCH G2 Die Sets The PUNCH G2 uses a variety of easily interchangeable die sets that allow you to punch documents in line for several different binding styles. By selecting the appropriate die set, you can use your PUNCH G2 to punch documents in any of the following binding styles. Heavy Duty (HD) die sets are shown in bold where available. Die Set Description Part Number For Plastic Comb Binding: 1 19-LTR 21-A4 PB Plastic Bind; Hole Size: 8mm x 2.9mm (0.313" x 0.116") (LxW); Center-to-Center Hole Spacing: 14.3mm (0.563") For Twin Loop™ Binding: Die, Konica Minolta, Comb Bind Die, Konica Minolta, Comb Bind, HD 7714911 1 32-LTR 34-A4 W3 Wire; Square; 3 Holes per inch; Hole Size: 4mm x 4mm (0.156" x 0.156") (L x W); Center-to-Center Hole Spacing: 8.5mm (0.333") 1 21-LTR 23-A4 W2 Wire; Rectangle; 2 Holes per inch; Hole Size: 6.4mm x 5.4mm (0.250" x 0.214")(L xW); Center-to-Center Hole Spacing: 12.7mm (0.500") 1 32-LTR 34-A4 W3 Wire; Round; 3 Holes per inch; Hole Size: 4mm (0.158") Diameter; Center-to-Center Hole Spacing: 8.5mm (0.335") Die, Konica Minolta, Wire 3.1, Sq. Die, Konica Minolta, Wire 2.1, Sq. Die, Konica Minolta, Wire, 3:1, Rnd. 7714913 7714912 7714903 1 21-LTR 23-A4 W2 Wire; Round; 2 Holes per inch; Hole Size: 6.5mm (0.0.256") Diameter; Center-to-Center Hole Spacing: 12.7mm (0.5") For Color Coil™ Binding: 1 44-LTR 47-A4 C4 Coil; Round; 4 Holes per inch; Hole Size: 4.4mm (0.174") Diameter; Center-to-Center Hole Spacing: 6.3mm (0.2475") 1 44-LTR 47-A4 C4 Coil; Oval; 4 Holes per inch; Hole Size: 4mm x 5mm (0.158" x 0.197") (L x W); Center-to-Center Hole Spacing: 6.3mm (0.2475") For Velo® Bind: Die, Konica Minolta, Wire, 2:1, Rnd. Die, Konica Minolta, Coil, Rnd. Die, Konica Minolta, Coil, Rnd, HD Die, Konica Minolta, Coil, Oval 7714902 7714901 7714917 7714914 1 11 VB Velobind®; Round; 1 Hole per inch Hole Size: 3.2mm (0.125") Diameter; Center-to-Center Hole Spacing: 25.4mm (1") 1 12 VB Velobind®; Round; 1 Hole per inch Hole Size: 3.2mm (0.126") Diameter; Center-to-Center Hole Spacing: 25.4mm (1") For Loose Leaf Binding: 1 3 3 Ring Binder; U.S. (Standard Loose-leaf Patterns); Hole Size: 8mm (0.316") Diameter Die, Konica Minolta, Velobind®, 11 Holes, Ltr. 7714909 Die, Konica Minolta, Velobind®, 12 Holes, A4. 7714910 Die, Konica Minolta, 3 Hole, 8mm Die, Konica Minolta, 3 Hole, 8mm, HD 7714904 7714918 1 7 3 Ring, 5 Ring, 7 Ring; U.S. (Standard Loose-leaf Patterns); Hole Size: 8mm (0.316") Diameter Die, Konica Minolta, 3/5/7 Hole, 8mm 7714905 1 4 4 Ring Binder; European (Standard Loose-leaf Patterns); Hole Size: 8mm (0.315") Diameter Die, Konica Minolta, 4 Hole, 8mm 7714906 1 4 4 Ring Binder; European (Standard Loose-leaf Patterns); Hole Size: 6.5mm (0.256") Diameter Die, Konica Minolta, 4 Hole, 6.5mm 7714907 Die, Konica Minolta, 4 Hole, Scan 7714908 4 Ring Binder; Scandinavian (Standard Loose-leaf Patterns); Hole Size: 6.5mm (0.256") Diameter ©2016 GBC, Lake Zurich, Illinois - All rights reserved. Graphics do not represent actual punch pattern dimensions or spacing. * When the Plastic Comb binding die is used in the 21 hole configuration on A4 width paper (297mm), there is the potential for the outer edge of holes 1 and 21 to be torn. The theoretical paper edge should be 1.62mm from the edge of the sheet. This event is dependent on paper type, paper width and hole alignment optimization. To avoid this issue, it is recommended to use a 20 hole configuration instead. 20 hole comb binding supplies are commonly available from GBC and other manufacturers and are considered more optimal than the 21 hole configuration. 12