Lantronix PremierWave XC PremierWave XC - Command Reference - Page 142

Restores the default xoff character on this line., default xoff char

Get Lantronix PremierWave XC PDF manuals and user guides View all Lantronix PremierWave XC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 142 highlights

clear line counters clrscrn command mode always command mode echo serial string disable command mode echo serial string enable command mode serial string command mode serial string command mode signon message command mode wait time configure current settings data bits 7 data bits 8 default baud rate default data bits default flow control default interface default parity default protocol default stop bits default threshold default xoff char default xon char exit flow control hardware flow control none flow control software gap timer interface rs232 interface rs485 full-duplex interface rs485 half-duplex interface usb-cdc-acm kill session line name PremierWave XC Command Reference 5: Commands and Levels = the speed. Standard speeds include 1200, 2400, 4800, 9600, 19200, and so on. Sets the serial counters to zero. Clears the screen. Sets the current line to always be in command mode. Disables user-defined serial boot string to be echoed in the CLI. Enables user-defined serial boot string to be echoed in the CLI. Enables user to enter a custom string at boot time to enter command mode. Sets a string that can be entered at boot time to enter command mode. = text with possible binary characters. Within [] use binary decimal up to 255 or hex up to 0xFF. Within {} specify decimal milliseconds time delay. Sets a sign-on message that is sent from the serial port when the device boots and when the line is in command mode. = text with possible binary characters. Within [] use binary decimal up to 255 or hex up to 0xFF. Sets boot-up wait time for command mode serial string. = wait time. Configures line with the current value of settings. Uses seven bits for data on the line. Uses eight bits for data on the line. Restores the default speed of 9600 bits per second. Restores the default of eight data bits. Restores the default of no flow control. Restores the default interface type to this line. Restores the default of no parity. Restores the default protocol on the line. Restores the default of one stop bit. Restores the factory default threshold. Restores the default xoff character on this line. Restores the default xon character on this line. Exits to the enable level Uses hardware (RTS/CTS) flow control on the line. Does not provide flow control on the line. Uses software (xon/xoff characters) flow control on the line. Sets the gap timer in milliseconds. If some data has been received, it will be forwarded after this time since the last character. Sets the line interface to RS232. Sets the line interface to RS485 in full-duplex mode. Sets the line interface to RS485 in half-duplex mode. Sets the line interface to USB-CDC-ACM mode. Kills command mode session on the Line Enters the line level. = number of the line (serial port) to be configured. Sets the name for this line. 142

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
5: Commands and Levels
PremierWave XC Command Reference
142
<bits per second> = the speed.
Standard speeds include 1200, 2400, 4800, 9600, 19200, and
so on.
clear line counters
Sets the serial counters to zero.
clrscrn
Clears the screen.
command mode always
Sets the current line to always be in command mode.
command mode echo serial string disable
Disables user-defined serial boot string to be echoed in the CLI.
command mode echo serial string enable
Enables user-defined serial boot string to be echoed in the CLI.
command mode serial string
Enables user to enter a custom string at boot time to enter
command mode.
command mode serial string
<string>
Sets a string that can be entered at boot time to enter com-
mand mode.
<string> = text with possible binary characters.
Within [] use binary decimal up to 255 or hex up to 0xFF.
Within {} specify decimal milliseconds time delay.
command mode signon message
<string>
Sets a sign-on message that is sent from the serial port when
the
device boots and when the line is in command mode.
<string> = text with possible binary characters.
Within [] use binary decimal up to 255 or hex up to 0xFF.
command mode wait time
<milliseconds>
Sets boot-up wait time for command mode serial string.
<milliseconds> = wait time.
configure current settings
Configures line with the current value of settings.
data bits 7
Uses seven bits for data on the line.
data bits 8
Uses eight bits for data on the line.
default baud rate
Restores the default speed of 9600 bits per second.
default data bits
Restores the default of eight data bits.
default flow control
Restores the default of no flow control.
default interface
Restores the default interface type to this line.
default parity
Restores the default of no parity.
default protocol
Restores the default protocol on the line.
default stop bits
Restores the default of one stop bit.
default threshold
Restores the factory default threshold.
default xoff char
Restores the default xoff character on this line.
default xon char
Restores the default xon character on this line.
exit
Exits to the enable level
flow control hardware
Uses hardware (RTS/CTS) flow control on the line.
flow control none
Does not provide flow control on the line.
flow control software
Uses software (xon/xoff characters) flow control on the line.
gap timer
<milliseconds>
Sets the gap timer in milliseconds. If some data has been re-
ceived, it will
be forwarded after this time since the last character.
interface rs232
Sets the line interface to RS232.
interface rs485 full-duplex
Sets the line interface to RS485 in full-duplex mode.
interface rs485 half-duplex
Sets the line interface to RS485 in half-duplex mode.
interface usb-cdc-acm
Sets the line interface to USB-CDC-ACM mode.
kill session
Kills command mode session on the Line
line
<line>
Enters the line level.
<line> = number of the line (serial port) to be configured.
name
<text>
Sets the name for this line.