Lantronix PremierWave XC PremierWave XC - Command Reference - Page 9

: Command Line Interface, Configuration Using Telnet, Serial Command Mode, Serial Recovery

Get Lantronix PremierWave XC PDF manuals and user guides View all Lantronix PremierWave XC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

3: Command Line Interface This chapter describes accessing the PremierWave XC by using Telnet, SSH, or serial ports to configure the PremierWave XC, navigating the Command Line Interface (CLI), typing keyboard shortcuts, and moving between the levels. It contains the following sections:  Configuration Using Telnet  Configuration Using Serial Ports  Navigating the CLI Hierarchy  Using Keyboard Shortcuts and CLI  Understanding the CLI Level Hierarchy Refer to Chapter 5: Commands and Levels for a complete list of levels, commands, and descriptions. Configuration Using Telnet To access and configure the device server by using a Telnet session over the network, you must first establish a Telnet connection. You can also establish a Telnet connection by clicking the Telnet Configuration tab in DeviceInstaller. See the DeviceInstaller Online Help for more information, available on our website www.lantronix.com/support/downloads. To access the PremierWave XC by using Telnet, perform the following steps. 1. Click Start > Run. The Run dialog box displays. 2. Type cmd in the dialog box and press OK. 3. Type telnet x.x.x.x (x.x.x.x is the IP address). The PremierWave XC is online when the command prompt (>) displays. You are at the root level of the CLI. Note: Depending on the level of security, a password may be required. Configuration Using Serial Ports Serial Command Mode The serial port can be configured to operate in command mode permanently or to be triggered under specified conditions. See the line Level command description for more information. Serial Recovery Serial Recovery mode will temporarily override the line and tunnel settings for the serial line to allow configuration changes to be made. The line and tunnel settings will be restored once the user exits the Serial Recovery mode CLI. PremierWave XC Command Reference 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
PremierWave XC Command Reference
9
3:
Command Line Interface
This chapter describes accessing the PremierWave XC by using Telnet, SSH, or serial ports to
configure the PremierWave XC, navigating the Command Line Interface (CLI), typing keyboard
shortcuts, and moving between the levels.
It contains the following sections:
Configuration Using Telnet
Configuration Using Serial Ports
Navigating the CLI Hierarchy
Using Keyboard Shortcuts and CLI
Understanding the CLI Level Hierarchy
Refer to
Chapter 5: Commands and Levels
for a complete list of levels, commands, and
descriptions.
Configuration Using Telnet
To access and configure the device server by using a Telnet session over the network, you must
first establish a Telnet connection. You can also establish a Telnet connection by clicking the
Telnet Configuration tab in DeviceInstaller. See the DeviceInstaller Online Help for more
information, available on our website
www.lantronix.com/support/downloads
.
To access the PremierWave XC by using Telnet, perform the following steps.
1.
Click
Start > Run
. The Run dialog box displays.
2.
Type
cmd
in the dialog box and press
OK
.
3.
Type
telnet x.x.x.x
(x.x.x.x is the IP address). The PremierWave XC is online when the
command prompt (>) displays.
You are at the root level of the CLI.
Note:
Depending on the level of security, a password may be required.
Configuration Using Serial Ports
Serial Command Mode
The serial port can be configured to operate in command mode permanently or to be triggered
under specified conditions. See the
line <line> Level
command description for more
information.
Serial Recovery
Serial Recovery mode will temporarily override the line and tunnel settings for the serial line to
allow configuration changes to be made. The line and tunnel settings will be restored once the
user exits the Serial Recovery mode CLI.