Lenovo E200 Hardware Maintenance Manual (HMM) - 3000 E200 (type 7848) - Page 72

signal

Get Lenovo E200 PDF manuals and user guides View all Lenovo E200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

Diagnostic Error Code 025-198-XXX IDE interface test aborted 025-199-XXX IDE interface test failed, cause unknown 030-000-XXX SCSI interface Test Passed 030-00X-XXX 030-01X-XXX SCSI interface failure 030-027-XXX SCSI interface Configuration/Setup error 030-03X-XXX 030-04X-XXX SCSI interface error 030-195-XXX SCSI interface Test aborted by user 030-196-XXX SCSI interface test halt, error threshold exceeded 030-197-XXX SCSI interface test warning FRU/Action 1. If a component is called out, make sure it is connected and/or enabled. See Chapter 6, "Using the Setup Utility," on page 49 2. Flash the system and re-test. See "Flash update procedures" on page 111 3. Go to "Undetermined problems" on page 78 1. Go to "Undetermined problems" on page 78 2. Flash the system and re-test. See "Flash update procedures" on page 111 3. Replace component under function test No action 1. SCSI signal cable 2. Check power supply 3. SCSI device 4. SCSI adapter card, if installed 5. System board 1. SCSI signal cable 2. Flash the system. See "Flash update procedures" on page 111 3. SCSI device 4. SCSI adapter card, if installed 5. System board 1. SCSI signal cable 2. Check power supply 3. SCSI device 4. SCSI adapter card, if installed 5. System board Information only Re-start the test, if necessary 1. Press F3 to review the log file 2. Re-start the test to reset the log file 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6, "Using the Setup Utility," on page 49 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test 66 Lenovo E200 Hardware Maintenance Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
Diagnostic
Error
Code
FRU/Action
025-198-XXX
IDE
interface
test
aborted
1.
If
a
component
is
called
out,
make
sure
it
is
connected
and/or
enabled.
See
Chapter
6,
“Using
the
Setup
Utility,”
on
page
49
2.
Flash
the
system
and
re-test.
See
“Flash
update
procedures”
on
page
111
3.
Go
to
“Undetermined
problems”
on
page
78
025-199-XXX
IDE
interface
test
failed,
cause
unknown
1.
Go
to
“Undetermined
problems”
on
page
78
2.
Flash
the
system
and
re-test.
See
“Flash
update
procedures”
on
page
111
3.
Replace
component
under
function
test
030-000-XXX
SCSI
interface
Test
Passed
No
action
030-00X-XXX
030-01X-XXX
SCSI
interface
failure
1.
SCSI
signal
cable
2.
Check
power
supply
3.
SCSI
device
4.
SCSI
adapter
card,
if
installed
5.
System
board
030-027-XXX
SCSI
interface
Configuration/Setup
error
1.
SCSI
signal
cable
2.
Flash
the
system.
See
“Flash
update
procedures”
on
page
111
3.
SCSI
device
4.
SCSI
adapter
card,
if
installed
5.
System
board
030-03X-XXX
030-04X-XXX
SCSI
interface
error
1.
SCSI
signal
cable
2.
Check
power
supply
3.
SCSI
device
4.
SCSI
adapter
card,
if
installed
5.
System
board
030-195-XXX
SCSI
interface
Test
aborted
by
user
Information
only
Re-start
the
test,
if
necessary
030-196-XXX
SCSI
interface
test
halt,
error
threshold
exceeded
1.
Press
F3
to
review
the
log
file
2.
Re-start
the
test
to
reset
the
log
file
030-197-XXX
SCSI
interface
test
warning
1.
Make
sure
the
component
that
is
called
out
is
connected
and/or
enabled.
See
Chapter
6,
“Using
the
Setup
Utility,”
on
page
49
2.
Re-run
test
3.
Replace
the
component
that
is
called
out
in
warning
statement
4.
Replace
the
component
under
test
66
Lenovo
E200
Hardware
Maintenance
Manual