Lenovo ThinkPad 560 TP 560Z On-line User's Guide that was provided with the sy - Page 144

Enabling or Disabling a Flash (POST/BIOS) Update from the Network

Get Lenovo ThinkPad 560 PDF manuals and user guides View all Lenovo ThinkPad 560 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 144 highlights

1 Go to the Easy-Setup menu. 2 Click on the Startup icon. The "Startup" window appears. 3 Click on the Network icon. The "Automatic Power on Startup Sequence" window appears. 4 Define a sequence by clicking on the devices in the order you want them to start. The devices you choose appear in boxes 1 to 4. 5 Click on OK. Note: If you want to change the settings, click on Reset and make the settings again. Enabling or Disabling a Flash (POST/BIOS) Update from the Network When a Flash (POST/BIOS) update from the network is enabled, the system programs in your computer can be updated remotely by a network administrator from a management console. The following requirements must be met, however: Update Flash from Network must also be enabled. (See the following steps.) Your computer must be started over the LAN. Your computer must be engaged in a remote program load. Network-management software is required in the remote administrator's computer. To enable or disable the Flash (POST/BIOS) update from Network setting, do the following: 1. Click on the CONFIG icon. The "Configuration" window appears. 2. Click on the Network icon. The "Network" window appears. 3. Select either the Enable or the Disable button beside "Flash." 138 IBM ThinkPad 560Z Online Book

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
1
Go to the Easy-Setup menu.
2
Click on the
Startup
icon.
The “Startup” window appears.
3
Click on the
Network
icon.
The “Automatic Power on Startup Sequence” window appears.
4
Define a sequence by clicking on the devices in the order you
want them to start.
The devices you choose appear in boxes 1 to 4.
5
Click on
OK
.
Note:
If you want to change the settings, click on
Reset
and make
the settings again.
Enabling or Disabling a Flash (POST/BIOS) Update from the
Network
When a Flash (POST/BIOS) update from the network is enabled, the
system programs in your computer can be updated remotely by a
network administrator from a management console.
The following
requirements must be met, however:
Update Flash from Network must also be enabled.
(See the
following steps.)
Your computer must be started over the LAN.
Your computer must be engaged in a remote program load.
Network-management software is required in the remote
administrator's computer.
To enable or disable the Flash (POST/BIOS) update from Network
setting, do the following:
1. Click on the
CONFIG
icon.
The “Configuration” window appears.
2. Click on the
Network
icon.
The “Network” window appears.
3. Select either the
Enable
or the
Disable
button beside “Flash.”
138
IBM ThinkPad 560Z Online Book