Lexmark C752 Setup Guide - Page 63

Step9: Con for TCP/IP, Assigning a printer IP address

Get Lexmark C752 PDF manuals and user guides View all Lexmark C752 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

Step 9: Configure for TCP/IP If you have TCP/IP available on your network, we recommend that you assign an IP address to the printer. Assigning a printer IP address Note: Instructions for other methods of setting the IP address are in the online documentation on the drivers CD that shipped with your printer. Launch the CD, click View Documentation Network Printer Install. If your network is using DHCP, an IP address is automatically assigned after you connect the network cable to the printer. 1 Look for the address under the "TCP/IP" heading on the network setup page you printed in "Printing a network setup page" on page 53. 2 Go to "Verifying the IP settings" on page 55 and begin with step 2. If your network is not using DHCP, then you must manually assign an IP address to the printer. One of the easiest ways is to use the operator panel: 1 Press Menu until you see Network Menu, and then press Select. 2 Press Menu until you see Standard Network, and then press Select. Standard Network appears if you purchased a printer with a network port on the printer system board. If you have a MarkNet print server installed in the option card, you see Network Option 1. 3 Press Menu until you see Std Net Setup (or Network 1 Setup), and then press Select. 4 Press Menu until you see TCP/IP, and then press Select. 5 Press Menu until you see Set IP Address, and then press Select. 6 Change the address by pressing Menu to increase or decrease each number. Press Select to move to the next segment. Press Select when you are finished. The message Saved appears briefly. Configure for TCP/IP 54

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
54
Configure for TCP/IP
Step 9: Configure for TCP/IP
If you have TCP/IP available on your network, we recommend that you
assign an IP address to the printer.
Assigning a printer
IP address
If your network is using DHCP,
an IP address is automatically assigned
after you connect the network cable to the printer.
1
Look for the address under the “TCP/IP” heading on the
network setup page you printed in “Printing a network setup
page” on page 53.
2
Go to “Verifying the IP settings” on page 55 and begin with
step 2.
Note:
Instructions for other
methods of setting the IP
address are in the online
documentation on the
drivers CD that shipped with
your printer. Launch the CD,
click
View Documentation
Network Printer Install
.
If your network is not using DHCP,
then you must manually assign an
IP address to the printer.
One of the easiest ways is to use the operator panel:
1
Press
Menu
until you see Network Menu, and then press
Select
.
2
Press
Menu
until you see Standard Network, and then press
Select
.
Standard Network appears if you purchased a printer with a
network port on the printer system board. If you have a MarkNet
print server installed in the option card, you see Network Option
1.
3
Press
Menu
until you see Std Net Setup (or Network 1 Setup),
and then press
Select
.
4
Press
Menu
until you see TCP/IP, and then press
Select
.
5
Press
Menu
until you see Set IP Address, and then press
Select
.
6
Change the address by pressing
Menu
to increase or decrease
each number. Press
Select
to move to the next segment. Press
Select
when you are finished.
The message
Saved
appears briefly.