LiftMaster SL595 SL595 Manual - Page 29

SINGLE PHASE WIRING DIAGRAM WARNING To protect against fire and electrocution: • DISCONNECT power BEFORE installing or servicing operator. • Replace ONLY with fuse of same type and rating. Fuse: 3AG, 3.2A, 120V, SLO-BLO GROUNDED (W) (W) 115V ONLY O/L (BK) (BK) 208/230V ONLY (W) 4B3 5A 6 (W) 4A3 1B 2 (W) 2A1 115V MOTOR CONNECTION (PU) (SL595 RD) (BL) (YE) (SL595 WH) (GY) SL595 GN) 42 8 5 13 (SEE NOTE 3) (BL/BK) (BK) 115V BRAKE (BK) SOLENOID (BL/BK) 1 PHASE POWER IN GROUND (BK) (BK) (BK) (BK) DUPLEX ON/OFF OUTLET SWITCH (115V ONLY) L1 (W) (S) (S) (SEE NOTE 2) 6B5 MOTOR OVERLOAD (SEE NOTE 3) PRIMARY L2 (W) BLACK (SL595 ORANGE) (BK) (B) (B) 115V ONLY (GN) (GN) (NOTE 4) (BL) 24V Sec. (SEE NOTE 1) FUSE (YE) 3.2A (BL) (TB 2) AB CD 208V/230V MOTOR CONNECTION (PU) (SL595 RD) 4 (SEE NOTE 3) (BL/BK) (BL) (YE) (SL595 WH) 83 (BK) 52 (BK) 230V BRAKE SOLENOID (GY) (SL595 GN) 1 (BL/BK) TO REVERSE MOTOR DIRECTION INTERCHANGE PURPLE & GRAY WIRES ON MODEL SL585 OR THE RED & GREEN WIRES ON MODEL SL595 INTERNAL MOTOR WIRING 1 - BLUE 2 - WHITE FACTORY INSTALLED RADIO RADIO BLOCK (BL) (BL) (BK) (BK) (YE) (YE) (YE) (YE) (RD) (RD) 3 - ORANGE 24VAC RADIO SIGNAL R1 (BL) R2 (BL) (YE) R3 (Y/BK) R4 (BRN) SAFETY ALARM (100 db) - (BK) + (RD) (SEE NOTE 5) 4 (GN) 6 (WH) 7 (RD) 8 (BK) 9 (BRN) 10 (GY) FREE EXIT LOOP HARNESS 10 PIN - 1,2,3,5 CAPPED 4 - YELLOW 5 - BLACK 8 - RED O/L - BROWN GL CONTROL BOARD J2 PLUG 24VAC-IN 24VAC-COMMON SOFT OPEN NC "B" LIMIT CONTACTOR B J2-3 J2-4 J2-5 J2-6 J2-7 J2-1 (BL) (YE) (GN) 3 L/S B (PU) 2 (PU) NC COM "A" LIMIT J2-8 CONTACTOR A J2-2 L/S A (OR) 1 NC COM (OR) RPM - IN RPM - SUPPLY RPM GND J2-9 J2-10 J2-11 (WH) (RD) (BK) RPM SENSOR J1 PLUG RADIO COMMAND J1-1 (PU) (Y/BK) (YE) B A1 A2 A A1 A2 OPEN CLOSE (Y/BK) (OR) (GN) SHADOW J1-2 (PU/WH) +24VDC J1-3 CLOSE J1-4 (Y/BK) (GN) 4 (GN) (WH) 6 INTERRUPT (SAFETY) 7 LOOP HARNESS (RD) 8 10 PIN - 1,2,3,5 (BK) 9 CAPPED (BRN) 10 (GY) (PU) (WH) (P/W) (Y/BK) (Y/BK) (GN) FIELD CONNECTIONS TB 1 1 RADIO 2 SHADOW 3 VDC COM 4 CLOSE STOP J1-5 SOFT OPEN J1-6 HARD OPEN J1-7 INT. LOOP J1-8 (Y/BK) (BRN) (OR) (GN) (Y/BK) STOP RESET (Y/BK) 5 (WH) STOP/COM (BRN) 6 SOFT OPEN (OR) 7 HARD OPEN (GN) 8 INTERRUPT (SAFETY) OBS. OPEN J1-9 OBS. CLOSE J1-10 24 VAC-COMMON J1-11 DC-GND J1-12 (GY) (OR/BK) (GY) 9 (OR/BK) 10 (WH) 11 (RD) 12 OPEN EDGE/PHOTOEYE (SAFETY) CLOSE MASTER / SECOND LOCK 1 J1-13 (BK) LOCK 1 J1-14 (BK) ALARM 1 J1-15 (BL) ALARM 1 J1-16 (RD) (BK) 13 (BK) 14 (BL) 15 (YE) 16 MAGLOCK 24 VAC DUAL GATE J4 PLUG 1 2 (WH) (RD) = TERMINAL BLOCK IN LIMIT SWITCH ENCLOSURE (SL595 ONLY). NOTES: (GY) 17 (BRN) 18 (GY) 19 (BRN) 20 INTERRUPT LOOP (SAFETY) EXIT LOOP 1. Transformer primary voltage same as operator line voltage 24V secondary 60VA. 2. Wire color: 115V black, 208V red, 230V orange. 3. Single phase units are equipped with an external line break device and may be equipped with an additional internal pilot duty thermal o/l device. 4. Outlet wiring: Black wire to brass screw, white wire to silver screw and green wire to green screw. 5. When using a remote control or Single Button Control Station in lieu of the Soft Open feature, perform the following modifications to the operator: 1. Remove the green wire from R4 of the radio block and mount the wire to terminal block TB1 position 6. 2. Move the brown wire on Terminal Block TB1 position 6 (from radio block R4) to Terminal Block TB1 position 1. 29