Maytag MED6300TQ Use and Care Guide - Page 27

Dryer

Get Maytag MED6300TQ - 29inch Front-Load Electric Dryer PDF manuals and user guides
UPC - 883049060958
View all Maytag MED6300TQ manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

4. Close the door. 5. Press the POWER button. 6. Select a timed drying cycle and temperature (see following chart). Items containing foam, rubber or plastic must be dried on a clothesline or by using the Air Fluff temperature setting. 7. You must select a time by pressing T]MED CYCI.E ADJUST Up or Down. Reset time as needed to complete drying. Refer to the following table. 8. Press (and hold) START button (about 1 second). [his chart shows examples of items that can be rack dried and the suggested cycle, temperature setting and drying time. Actual drying time will depend on the amount of moisture items hold. Rack Dry Wool Sweaters Block to shape and lay flat on the rack. Stuffed toys or pillows Cotton or polyester fiber filled Stuffed toys or pillows Foam rubber filled Setting Timed Dry Timed Dry Timed Dry Temp. Low Time* 60 low 60 Air Fluff (no 90 heat) Sneakers or canvas shoes Timed Dry Air Fluff (no 90 he at ) *(Minutes) Reset time to complete drying, if needed. DRYER CARE CLEANING THE DRYER LOCATION Keep dryer area clear and free from items that would obstruct the flow of combustion and ventilation air. Every load cleaning 1. The lint screen is located on the top of the dryer. Pull the lint screen toward you. Roll lint off the screen with your fingers. Do not rinse or wash screen to remove lint. Wet lint is hard to remove. Explosion Hazard Keep flammable materials and vapors, such as gasoline, away from dryer. Place dryer at least 18 inches (46 cm) above the floor for a garage installation, Failure to do so can result in death, explosion, or fire. CLEANING THE LINT SCREEN Clean the lint screen before each load. A screen blocked by lint can increase drying time. IMPORTANT: • Do not run the dryer with the lint screen loose, damaged, blocked or missing. E)oing so can cause overheating and damage to both the dryer and fabrics. • ]f lint falls off the screen into the dryer during removal, check the exhaust hood and remove the lint. 2. Push the lint screen firmly back into place. As needed cleaning 1. Roll lint off screen with your fingers. 2. Wet both sides of lint screen with hot water. 3. Wet a nylon brush with hot water and liquid detergent. Scrub lint screen with the brush to remove residue buildup. 4. Rinse screen with hot water. 5. Thoroughly dry lint screen with a clean towel. Insert lint screen back into dryer.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
4.
Close
the
door.
5.
Press the
POWER
button.
6.
Select
a timed
drying
cycle
and temperature
(see following
chart).
Items
containing
foam,
rubber
or plastic
must
be dried
on a clothesline
or by using
the
Air
Fluff
temperature
setting.
7.
You must select
a time
by pressing
T]MED
CYCI.E
ADJUST
Up
or Down.
Reset time
as
needed
to complete
drying.
Refer to the following
table.
8.
Press (and
hold)
START
button
(about
1 second).
[his
chart
shows
examples
of items
that
can be rack
dried
and
the
suggested
cycle,
temperature
setting
and
drying
time.
Actual
drying
time
will
depend
on the
amount
of
moisture
items
hold.
Rack Dry
Setting
Temp.
Time*
Wool
Sweaters
Timed
Dry
Low
60
Block
to shape
and
lay flat
on
the
rack.
Stuffed
toys or pillows
Timed
Dry
low
60
Cotton
or polyester
fiber
filled
Stuffed
toys or pillows
Timed
Dry
Air
Fluff
(no
90
Foam
rubber
filled
heat)
Sneakers
or
canvas shoes
Timed
Dry
Air
Fluff
(no
90
he at
)
*(Minutes)
Reset time
to complete
drying,
if needed.
DRYER
CARE
CLEANING
THE
DRYER
LOCATION
Keep dryer
area clear
and
free from
items
that
would
obstruct
the flow
of
combustion
and
ventilation
air.
Explosion
Hazard
Keep
flammable
materials
and
vapors,
such
as
gasoline,
away
from
dryer.
Place
dryer
at least
18
inches
(46
cm)
above
the
floor
for
a garage
installation,
Failure
to
do
so
can
result
in death,
explosion,
or fire.
CLEANING
THE
LINT SCREEN
Clean
the
lint
screen
before
each
load.
A screen
blocked
by lint
can
increase
drying
time.
IMPORTANT:
•
Do
not
run the
dryer
with
the
lint
screen
loose,
damaged,
blocked
or missing.
E)oing
so
can cause
overheating
and
damage
to both
the
dryer
and
fabrics.
•
]f
lint
falls
off the
screen
into
the dryer
during
removal,
check
the
exhaust
hood
and
remove
the
lint.
Every
load
cleaning
1.
The lint
screen
is located
on the
top
of the dryer.
Pull
the
lint
screen
toward
you.
Roll
lint
off
the screen
with
your
fingers.
Do
not
rinse
or wash
screen
to
remove
lint.
Wet
lint
is
hard
to remove.
2.
Push the
lint
screen
firmly
back
into
place.
As needed
cleaning
1.
Roll
lint
off
screen
with
your
fingers.
2.
Wet
both
sides of
lint
screen
with
hot water.
3.
Wet
a nylon
brush
with
hot
water
and
liquid
detergent.
Scrub
lint
screen
with
the brush
to
remove
residue
buildup.
4.
Rinse
screen
with
hot water.
5.
Thoroughly
dry
lint
screen
with
a clean
towel.
Insert
lint
screen
back
into
dryer.