Oki MICROLINE 390 TURBO Printer Handbook - Page 85

SI Select Pitch 10 CPI.

Page 85 highlights

Proportional Spacing. No (factory default) or Yes. Change to Yes to engage proportional spacing of characters. Protocol. Appears only if optional Serial Interface is installed. Selects the type of protocol your system uses: Ready/Busy (factory default) or X-On/X-Off. Receive Buffer Size. 64K (factory default), 1 Line, 32K, or 79K. Selects the amount of memory devoted to holding received data. Choosing 1 Line will tie up your computer during printing, but if you about the print job the printer will stop printing much sooner. Reset Inhibit. No (factory default) or Yes. Change to Yes if you want your printer to ignore the reset command sent by software. This will prevent your software reset command from changing the settings you have made through the front panel controls or through printer commands. If you engage this feature, don't forget that it will also prevent your software from clearing out existing settings when you finish printing one document and switch to another. Serial Data 7/8 Bits. Appears only if optional Serial Interface is installed. 8 Bits (factory default) or 7 Bits. Change to 7 bits if your system uses a 7-bit data format. SI Select Pitch (10 CPI). IBM mode only. 17.1 CPI (factory default) or 15 CPI. Sets what pitch (17.1 or 15 characters per inch) will be engaged when the printer control panel is set for 10 cpi and the SI command is received. SI Select Pitch (12 CPI). IBM mode only. 20 CPI (factory default) or 12 CPI. Sets what pitch (20 or 12 characters per inch) will be engaged when the printer control panel is set for 12 cpi and the SI command is received. Size. Choose Single (factory default) or Double width and height printing. Skip Over Perforation. No (factory default) or Yes. Change to Yes if you want the printer to advance automatically to the next page when it comes within one inch of the bottom of the page. If your software has its own page formatting controls, keep this item set to No to avoid interface. Style. Choose Normal (factory default) or Italics. 78 Appendix B: Menu Selections

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135

78
Appendix B: Menu Selections
Proportional Spacing.
No (factory default) or Yes. Change to Yes to engage propor-
tional spacing of characters.
Protocol.
Appears only if optional Serial Interface is installed. Selects the type of pro-
tocol your system uses: Ready/Busy (factory default) or X-On/X-Off.
Receive Buffer Size.
64K (factory default), 1 Line, 32K, or 79K. Selects the amount of
memory devoted to holding received data. Choosing 1 Line will tie up your computer
during printing, but if you about the print job the printer will stop printing much sooner.
Reset Inhibit.
No (factory default) or Yes. Change to Yes if you want your printer to
ignore the reset command sent by software. This will prevent your software reset
command from changing the settings you have made through the front panel con-
trols or through printer commands. If you engage this feature, don’t forget that it will
also prevent your software from clearing out existing settings when you finish print-
ing one document and switch to another.
Serial Data 7/8 Bits.
Appears only if optional Serial Interface is installed. 8 Bits (fac-
tory default) or 7 Bits. Change to 7 bits if your system uses a 7-bit data format.
SI Select Pitch (10 CPI).
IBM mode only. 17.1 CPI (factory default) or 15 CPI. Sets
what pitch (17.1 or 15 characters per inch) will be engaged when the printer control
panel is set for 10 cpi and the SI command is received.
SI Select Pitch (12 CPI).
IBM mode only. 20 CPI (factory default) or 12 CPI. Sets what
pitch (20 or 12 characters per inch) will be engaged when the printer control panel is
set for 12 cpi and the SI command is received.
Size.
Choose Single (factory default) or Double width and height printing.
Skip Over Perforation.
No (factory default) or Yes. Change to Yes if you want the
printer to advance automatically to the next page when it comes within one inch of
the bottom of the page. If your software has its own page formatting controls, keep
this item set to No to avoid interface.
Style.
Choose Normal (factory default) or Italics.