Onkyo TX-NR626 Owner's Manual English - Page 21

Turning On & Basic Operations, Turning On/Off the AV Receiver, Connecting the Power Cord, Turning - problems

Get Onkyo TX-NR626 PDF manuals and user guides View all Onkyo TX-NR626 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Turning On & Basic Operations Turning On/Off the AV Receiver Connecting the Power Cord 1 (Taiwanese models) Connect the supplied power cord to the AV receiver's AC INLET. To AC wall outlet the same circuit. If this is a problem, plug the AV receiver into a different branch circuit. • Do not use a power cord other than the one supplied with the AV receiver. The supplied power cord is designed exclusively for use with the AV receiver and should not be used with any other equipment. • Never disconnect the power cord from the AV receiver while the other end is still plugged into a wall outlet. Doing so may cause an electric shock. Always disconnect the power cord from the wall outlet first, and then the AV receiver. Turning On 1 Press ON/STANDBY on the front panel. or Press RECEIVER followed by RECEIVER on the remote controller. The AV receiver comes on and its display lights. ■ Smooth Operation in a Few Easy Steps (Initial Setup) To ensure smooth operation, here's a few easy steps to help you configure the AV receiver before you use it for the very first time. These settings only need to be made once. See "Initial Setup" for details (➔ page 22). Turning On & Basic Operations Turning Off 1 Press ON/STANDBY on the front panel. or Press RECEIVER followed by RECEIVER on the remote controller. The AV receiver will enter standby mode. To prevent any loud surprises when you turn on the AV receiver, always turn down the volume before you turn it off. Tip • The HYBRID STANDBY indicator may light depending on the status of settings (➔ page 22). • For details on power management settings, see "Auto Standby" (➔ page 66). • If the HDMI Through setting is not set in standby mode, an MHL-enabled mobile device cannot be charged even if it is connected. 2 Plug the power cord into an AC wall outlet. Note • Before connecting the power cord, connect all of your speakers and AV components. • Turning on the AV receiver may cause a momentary power surge that might interfere with other electrical equipment on En-21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
En-21
Turning On & Basic Operations
Turning On/Off the AV
Receiver
Note
• Before connecting the power cord, connect all of your
speakers and AV components.
•
Turning on the AV receiver may cause a momentary power
surge that might interfere with other electrical equipment on
the same circuit. If this is a problem, plug the AV receiver
into a different branch circuit.
• Do not use a power cord other than the one supplied with
the AV receiver. The supplied power cord is designed
exclusively for use with the AV receiver and should not be
used with any other equipment.
• Never disconnect the power cord from the AV receiver
while the other end is still plugged into a wall outlet. Doing
so may cause an electric shock. Always disconnect the
power cord from the wall outlet first, and then the AV
receiver.
■
Smooth Operation in a Few Easy Steps
(Initial Setup)
To ensure smooth operation, here’s a few easy steps
to help you configure the AV receiver before you use
it for the very first time. These settings only need to
be made once. See “Initial Setup” for details
(
➔
page 22
).
Tip
• The
HYBRID STANDBY
indicator may light depending on
the status of settings (
➔
page 22
).
• For details on power management settings, see “Auto
Standby” (
➔
page 66
).
•
If the HDMI Through setting is not set in standby mode, an
MHL-enabled mobile device cannot be charged even if it is
connected.
Turning On & Basic
Operations
Connecting the Power Cord
1
(Taiwanese models)
Connect the supplied power cord to the AV
receiver’s AC INLET.
2
Plug the power cord into an AC wall outlet.
To AC wall outlet
Turning On
1
Press
8
ON/STANDBY on the front panel.
or
Press RECEIVER followed by
8
RECEIVER on
the remote controller.
The AV receiver comes on and its display lights.
Turning Off
1
Press
8
ON/STANDBY on the front panel.
or
Press RECEIVER followed by
8
RECEIVER on
the remote controller.
The AV receiver will enter standby mode. To
prevent any loud surprises when you turn on the
AV receiver, always turn down the volume before
you turn it off.