Onkyo TX-SR601 Owner Manual - Page 30

& Canadian models and European models

Get Onkyo TX-SR601 PDF manuals and user guides View all Onkyo TX-SR601 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Connecting antennas Connecting an FM outdoor antenna Make sure to follow the general rules given below: • Keep the antenna away from noise sources (neon signs, busy roads, etc.). • It is dangerous to put the antenna close to power lines. Keep it well away from power lines, transformers, etc. Directional linkage Do not use the same antenna for both FM and TV (or VCR) reception since the FM and TV (or VCR) signals can interfere with each other. If you must use a common FM/TV (or VCR) antenna, use a directional linkage type splitter. ANTENNA AM FM 75 ZONE 2 LINE OUT L AL VIDEO 3 IN VIDEO 2 OUT IN R VIDEO 1 OUT IN DVD MO IN OU Connecting an AM outdoor antenna If reception is poor with the indoor AM antenna, stretch out the outdoor antenna (16 feet (5 meters) or more) above a window or outside. • Keep the indoor AM loop antenna connected. Do not remove it. Outdoor antenna (Indoor) AM loop antenna ANTENNA AM FM 75 ZONE 2 LINE OUT L L VIDEO 3 IN VIDEO 2 OUT IN R VIDEO 1 OUT IN DVD M IN O Note: If you are using the TX-SR701/701E/601/601E worldwide model in a region where AM frequencies are delineated by 10-kHz steps, be sure to set the "AM Frequency Step" Setup setting accordingly (see page 55). To receiver To TV (or VCR) Connecting the antenna cable to the 75/300 Ω antenna adapter (For all models other than USA & Canadian models and European models) Connecting the 300 Ω ribbon wire: Loosen the screws on the adapter and wrap the wires of the ribbon wire around these screws. Then tighten the screws down with a screwdriver. Outdoor antenna 300 Ω ribbon wire Connecting the coaxial cable: 1. With your fingernail, or a small screwdriver, press the stoppers of the 75/300 Ω antenna adapter outward and remove the cover. 2. Remove the transformer wire A from slit B and insert it into slit C. 3. Prepare the coaxial cable as shown in the diagram. 4. Connect the 75/300 Ω antenna adapter to the coaxial cable. 1. Insert the end of the cable. 2. Clamp it in place with pliers. 3. Reinstall the cover. 1 2 3, 4 Slit B ✦ ✦ ✦✦ ✦ ✦ 636 mm mm mm 5/8" (15mm) Wire A Slit C 30

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
30
Connecting antennas
Make sure to follow the general rules given below:
•
Keep the antenna away from noise sources (neon signs, busy
roads, etc.).
•
It is dangerous to put the antenna close to power lines. Keep it
well away from power lines, transformers, etc.
If reception is poor with the indoor AM antenna, stretch out the
outdoor antenna (16 feet (5 meters) or more) above a window or
outside.
•
Keep the indoor AM loop antenna connected. Do not remove it.
Note:
If you are using the TX-SR701/701E/601/601E worldwide model in
a region where AM frequencies are delineated by 10-kHz steps, be
sure to set the “AM Frequency Step” Setup setting accordingly (see
page 55).
Connecting an FM outdoor antenna
Connecting an AM outdoor antenna
VIDEO 2
DVD
MO
OU
VIDEO 1
VIDEO 3
IN
IN
IN
IN
OUT
OUT
AL
ANTENNA
FM 75
AM
R
L
ZONE 2
LINE OUT
VIDEO 2
DVD
M
O
VIDEO 1
VIDEO 3
IN
IN
IN
IN
OUT
OUT
L
ANTENNA
FM 75
AM
R
L
ZONE 2
LINE OUT
Outdoor antenna
(Indoor)
AM loop antenna
Do not use the same antenna for both FM and TV (or VCR)
reception since the FM and TV (or VCR) signals can interfere with
each other. If you must use a common FM/TV (or VCR) antenna,
use a directional linkage type splitter.
Connecting the 300
Ω
ribbon wire:
Loosen the screws on the adapter and wrap the wires of the ribbon
wire around these screws. Then tighten the screws down with a
screwdriver.
Connecting the coaxial cable:
1.
With your
fi
ngernail, or a small screwdriver, press the
stoppers of the 75/300
Ω
antenna adapter outward
and remove the cover.
2.
Remove the transformer wire A from slit B and insert
it into slit C.
3.
Prepare the coaxial cable as shown in the diagram.
4.
Connect the 75/300
Ω
antenna adapter to the coaxial
cable.
1.
Insert the end of the cable.
2.
Clamp it in place with pliers.
3.
Reinstall the cover.
Directional linkage
Connecting the antenna cable to the 75/300
Ω
antenna adapter (For all models other than USA
& Canadian models and European models)
To TV (or VCR)
To receiver
Outdoor
antenna
300
Ω
ribbon wire
1
2
3, 4
✦
✦
✦
✦
✦
✦
✦
✦
✦
✦
✦
6
mm
3
mm
6
mm
5/8"
(15mm)
Wire A
Slit C
Slit B