Onkyo TX-SR601 Owner Manual - Page 71

Programming the commands of remote controllers, for other devices into the remote controller

Get Onkyo TX-SR601 PDF manuals and user guides View all Onkyo TX-SR601 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

Programming the commands of remote controllers for other devices into the remote controller INMPULUTTI-CH MOSDUER CD SLEEP POWER VIDEO-2 DVGTDRAOPUEPINPTUUTTNSUEPENRLREEERCSPTEDITHOMORNMEOR 2 to 6 inches (5 to 15 cm) SEND/LEARN indicator MODE buttons DVD VIDEO-1 CD TOTNEEST VOLUME DISC TAPE CH SEL MUTING 85S Programming procedure When programming the commands of another remote controller to the RC-533M/515M remote controller, you must first decide under which MODE button you want the commands to be linked. In general, you will select the MODE button that corresponds to the component you are programming. For example, if you are programming the functions from a remote controller for a compact disc player, you would choose the CD MODE button. Then, by pressing the CD MODE button, the buttons on the RC-533M/515M remote controller will change to the commands you program here to operate the compact disc player. After programming which MODE button to use, you will then transfer the separate commands from the other remote controller over to the RC-533M/515M remote controller one at a time. Each command is then programmed to a different button on the RC533M/515M remote controller. Any button is programmable for this step except for the eight MODE buttons (RCVR, CD, DVD, SAT/ MD, TV, VCR, and CABLE), the two MACRO buttons (1 and 2), and the LIGHT button (RC-533M only). Even after the commands have been memorized, keep your old remote controller in a safe place. If for some reason the commands are lost (e.g., when the batteries run down), it will be necessary to memorize them once again. 1. Place the remote controller and the remote controller for the other device facing each other at a distance of 2 to 6 inches (5 to 15 cm) apart. 2. While pressing and holding down the desired MODE button on the remote controller, press the ENTER button and then release both buttons. The SEND/LEARN indicator lights when the MODE button is pressed and turns off when the ENTER button is pressed. When the indicator turns off, release both buttons. The SEND/LEARN indicator lights again. 3. Press and release the button on the remote controller to which you want to transfer the next command. You may select any button excluding the eleven ones indicated in the figure below. When you press the button, the SEND/ LEARN indicator turns off. When you release the button, the indicator lights again. If you press the wrong button by mistake, press that same button again. The SEND/LEARN indicator flashes twice, and the remote controller exits the programming mode. ENTER MACRO 1 LIGHT MACRO 2 MODE buttons : Buttons that cannot be programmed 71

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
71
Programming the commands of remote controllers
for other devices into the remote controller
POWER
SLEEP
DIMMER
SUR
MODE
VIDEO-1
VIDEO-2
TAPE
DVD
C D
C D
DVD
TUNER
TUNER
PHONO
INPUT SELECTOR
DISC
TAPE
VOLUME
CH SEL
PRESET
MUTING
TEST
TONE
MULTI-CH
INPUT
GROUP
85S
2 to 6 inches
(5 to 15 cm)
ENTER
SEND/LEARN
indicator
MODE buttons
When programming the commands of another remote controller to
the RC-533M/515M remote controller, you must first decide under
which MODE button you want the commands to be linked. In
general, you will select the MODE button that corresponds to the
component you are programming. For example, if you are
programming the functions from a remote controller for a compact
disc player, you would choose the CD MODE button. Then, by
pressing the CD MODE button, the buttons on the RC-533M/515M
remote controller will change to the commands you program here to
operate the compact disc player.
After programming which MODE button to use, you will then
transfer the separate commands from the other remote controller
over to the RC-533M/515M remote controller one at a time. Each
command is then programmed to a different button on the RC-
533M/515M remote controller. Any button is programmable for this
step except for the eight MODE buttons (RCVR, CD, DVD, SAT/
MD, TV, VCR, and CABLE), the two MACRO buttons (1 and 2),
and the LIGHT button (RC-533M only).
Even after the commands have been memorized, keep your old
remote controller in a safe place. If for some reason the commands
are lost (e.g., when the batteries run down), it will be necessary to
memorize them once again.
1.
Place the remote controller and the remote controller
for the other device facing each other at a distance of
2 to 6 inches (5 to 15 cm) apart.
2.
While pressing and holding down the desired MODE
button on the remote controller, press the ENTER
button and then release both buttons.
The SEND/LEARN indicator lights when the MODE button is
pressed and turns off when the ENTER button is pressed. When
the indicator turns off, release both buttons. The SEND/LEARN
indicator lights again.
3.
Press and release the button on the remote controller
to which you want to transfer the next command.
You may select any button excluding the eleven ones indicated
in the figure below. When you press the button, the SEND/
LEARN indicator turns off. When you release the button, the
indicator lights again.
If you press the wrong button by mistake, press that same button
again. The SEND/LEARN indicator flashes twice, and the
remote controller exits the programming mode.
Programming procedure
:
MACRO 1
MACRO 2
LIGHT
Buttons that cannot be programmed
MODE buttons