Onkyo TX-SR601 Owner Manual - Page 60
Enjoying music in the remote zone
View all Onkyo TX-SR601 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 60 highlights
Enjoying music in the remote zone ZONE 2 indicator OFF STANDBY/ON AUDIO ADJUST SETUP RETURN TUNI NG MASTER VOLUME POWER ON OFF REC OUT ZONE 2 OFF LEVEL STANDBY DISPLAY RT/PTY/TP STEREO LISTENING MODE SURROUND THX DSP PRESET MEMORY FM MODE CLEAR PHONES DIRECT/ PURE AUDIO PURE AUDIO AUDIO SELECTOR DVD VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4 VCR 1 VCR 2 TAPE TUNER CD PHONO ENTER VIDEO 4 INPUT DIGITAL S VIDEO VIDEO L AUDIO R ZONE 2 Input source buttons ON/STANDBY LEVEL / INPUT SELECTOR buttons ZONE 2 Using the buttons 1. Press the ZONE 2 button. 2. Select an input source. After pressing the ZONE 2 button, you must press an input source button within 5 seconds. The ZONE 2 indicator lights. Ex.: When the CD button is pressed. Using the remote controller With the TX-SR701/701E/601/601E in the standby state, turn on the output to the remote zone (Zone 2): After pressing the ZONE 2 button, press the ON button within 5 seconds. The ZONE 2 indicator lights. To select the same source for the remote zone that is selected for the main zone, press the ZONE 2 button again until "Zone2Sel:SOURCE" appears in the display. • When "Zone2Sel:Off" is displayed, the output to the remote zone is turned off. • When you are not using the remote zone (Zone 2), press the OFF button to turn off the ZONE 2 indicator. Notes: • If a sleep time is set with the SLEEP button, the output to the remote zone will also turn off when the sleep time elapses. • If the source for the main zone is selected as the source for the remote zone and the source for the main zone is changed, then the source for the remote zone will change as well. • The ZONE 2 terminal is an analog output. Digital signals are not output. If no sound is heard from the selected input source, check if the component is connected to the analog inputs. • If the REC OUT button is pressed in the main room while someone is using the system in the remote zone, the Zone 2 function will be deactivated and the source will turn off in the remote zone. • If you select FM (or AM) with the TUNER input source button when the source for the remote zone (Zone 2) is set to AM (or FM), the output for the remote zone also changes to FM (or AM). • When you are using the remote zone (Zone 2), operation will not work. system • In the remote zone, you can only play the source in the 2channel mode. You cannot play the source in the remote zone in the surround mode. To turn off output to the remote zone (Zone 2), press the ZONE 2 button and then the STANDBY button within 5 seconds. Select an input source: After pressing the ZONE 2 button, press an input source button within 5 seconds. If tuner is selected with the TUN button, you can use the CH button to select a preset radio station. Note: After you press the ZONE 2 button on the remote controller, the ZONE 2 indicator on the TX-SR701/701E/601/601E flashes for five seconds. During this time, you will not be able to perform operations in the main zone using the remote controller. Adjusting the volume for the remote zone When the remote zone (Zone 2) speakers are connected to the ZONE 2 SPEAKERS terminals, or to an amplifier connected to the ZONE 2 PRE OUT terminals, adjust the volume as shown below. Press the LEVEL / buttons on the front panel. Adjusting the volume (using the remote controller): After pressing the ZONE 2 button, the ZONE 2 indicator on the TX-SR701/701E/601/601E will flash for 5 seconds. During this time press the LEVEL / button. 60