Onkyo TX-SR601 Owner Manual - Page 74

Erasing a macro from the MACRO 1 or 2 button, Erasing all commands and macros that have, been

Get Onkyo TX-SR601 PDF manuals and user guides View all Onkyo TX-SR601 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

Using the macro function MACRO 1 SEND/LEARN indicator MACRO 2 MODE buttons ENTER Erasing a macro from the MACRO 1 (or 2) button 1. Press and hold down any one of the seven MODE buttons, press the MACRO 1 (or 2) button, and then release both buttons. When you press the MODE button, it lights and the SEND/ LEARN indicator lights. When you press the MACRO 1 (or 2) button, the indicator turns off. When you release the buttons, the indicator flashes once. 2. Press the MACRO 1 (or 2) button again. The SEND/LEARN indicator slowly flashes twice. The macro programmed to the MACRO button is erased. Notes: • If the SEND/LEARN indicator quickly flashes three times and turns off, then the remote controller has exited the erasing mode because either you have made a mistake during erasing or a time-out has occurred because no button has been pressed. Resume from Step 1. • If you press a button other than MACRO 1 (or 2) button in Step 2, then you will in effect be overwriting the previous macro with a new macro. Erasing all commands and macros that have been programmed SEND/LEARN indicator This procedure will erase all the commands and macros that you have programmed into the remote controller and return it to its default settings. This operation will not affect the preset settings of ON STANDBY the remote controller. 1. Open the battery cover and remove the batteries from the remote controller. 2. While pressing and holding down the ON and STANDBY buttons, re-insert the batteries in their correct orientation, and then release both buttons. The SEND/LEARN indicator flashes slowly. 3. Press the ENTER button. The SEND/LEARN indicator lights up for about ten seconds and then turns off. All programmed commands and macros are erased and the remote controller returns to its factory presets. ENTER Notes: • Proceed to Step 3 immediately after Step 2; otherwise, the batteries will be consumed quickly. • If you press any button other than the ENTER button in Step 3, nothing will be erased. In this case, resume from Step 1. 74

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
74
Using the macro function
ENTER
MACRO 1
MACRO 2
SEND/LEARN
indicator
MODE buttons
ENTER
ON
STANDBY
SEND/LEARN
indicator
1.
Press and hold down any one of the seven MODE
buttons, press the MACRO 1 (or 2) button, and then
release both buttons.
When you press the MODE button, it lights and the SEND/
LEARN indicator lights. When you press the MACRO 1 (or 2)
button, the indicator turns off. When you release the buttons, the
indicator flashes once.
2.
Press the MACRO 1 (or 2) button again.
The SEND/LEARN indicator slowly flashes twice. The macro
programmed to the MACRO button is erased.
Notes:
•
If the SEND/LEARN indicator quickly flashes three times and
turns off, then the remote controller has exited the erasing mode
because either you have made a mistake during erasing or a
time-out has occurred because no button has been pressed.
Resume from Step 1.
•
If you press a button other than MACRO 1 (or 2) button in Step
2, then you will in effect be overwriting the previous macro
with a new macro.
This procedure will erase all the commands and macros that you
have programmed into the remote controller and return it to its
default settings. This operation will not affect the preset settings of
the remote controller.
1.
Open the battery cover and remove the batteries from
the remote controller.
2.
While pressing and holding down the ON and
STANDBY buttons, re-insert the batteries in their
correct orientation, and then release both buttons.
The SEND/LEARN indicator flashes slowly.
3.
Press the ENTER button.
The SEND/LEARN indicator lights up for about ten seconds
and then turns off.
All programmed commands and macros are erased and the remote
controller returns to its factory presets.
Notes:
•
Proceed to Step 3 immediately after Step 2; otherwise, the
batteries will be consumed quickly.
•
If you press any button other than the ENTER button in Step 3,
nothing will be erased. In this case, resume from Step 1.
Erasing a macro from the MACRO 1 (or 2) button
Erasing all commands and macros that have
been programmed