Onkyo TX-SR876 Owner Manual - Page 140

Controlling Other Components-Continued LEVEL MUTING Learning Commands The AV receiver's remote controller can learn the commands of other remote controllers. By transmitting, for example, the Play command from your CD player's remote controller, the remote controller can learn it, and then transmit the exact same command when its Play [] button is pressed in the CD remote mode. This is useful when you've entered the appropriate remote control code (page 137) but some buttons don't work as expected. 1 1, 4 1 ON STANDBY TV INPUT DVD 1 VCR/DVR CBL/SAT 2 3 GAME/TV AUX1 AUX2 4 5 6 + TV CH - TAPE TUNER CD 7 8 9 PHONO NET/USB D. TUN TV VOL +10 0 CLEAR --/--- 10 11 12 INPUT SELECTOR MACRO 1 2 3 ZONE3 DVD REMOTE MODE VCR CD ZONE2 CDR/MD/DOCK TV DIMMER + CH DISC ALBUM - PREV CH DISPLAY CABLE SAT TOP MENU NET/USB RECEIVER TAPE/AMP SLEEP MENU ENTER VOL GUIDE SETUP EXIT RETURN MUTING Remote indicator While holding down the REMOTE MODE button for the mode in which you want to use the command, press the [ON] button. The Remote indicator lights up. 2 3 140 Press the button you want to learn the new command. Point the remote controllers at each other, about 2 to 6 inches (5-15 cm) apart, and then press and hold the button whose command you want to learn until the Remote indicator flashes. If the command is learned successfully, the Remote indicator flashes twice. R TOTNEEST VOLUME DISC TAPE CH SEL VIDEO-2 DVGTDRAOPUEPINPTUUTTNSUEPENRLREEERCSPTEDITHOMORNMEOR MOSDUER CD INMPULUTTI-CH VIDEO-1 CD SLEEP DVD About 2 to 6 inches (5-15 cm) POWER ON DVD SATCABLE + VN1ECT/RUSCBRDTRESA/MMLPED-OE/E-D/TA/PROI-C2ENMECM-CDEP-PKM+IAVU1ECO1RT00RDPSOEHEOLZNEOO3CNTE70O211RTNAEPTZ/OEUNSEB4C83LG1E2ATARMUDEN.T/ETUVNR159 DVD AUX1 2DCR/DVR 6 AUX2 CD TV VOL STANDBY 3 CBL/SAT I - TV CH T V INPUT Supplied remote controller (RC-687M) 4 To learn more commands, repeat steps 2 and 3. Press any REMOTE MODE button when you've finished. Notes: • The following buttons cannot learn new commands: REMOTE MODE, MACRO [1], [2], [3], TV CH [+]/[-], Re-EQ, LIGHT. • When you want to learn the command from your TV's Power button, select the TV remote control mode and use the remote controller's [STANDBY] button to learn the command. In the TV remote control mode, the remote controller's [STANDBY] and TV [] buttons are linked, so using the [STANDBY] button to learn the command will mean that you can also use the TV [] button to turn your TV on or off in TV remote control mode. • When you want to learn the commands from your TV's Channel Up and Down buttons, select the TV remote control mode and use the remote controller's CH [+/-] button (left to the [ENTER] button) to learn the commands. In the TV remote control mode, the remote controller's CH [+/-] and TV CH [+]/[-] buttons are linked, so using the CH [+/-] button to learn these commands will mean that you can also use the TV CH [+]/[-] buttons to change channels in TV remote control mode. • The remote controller can learn approximately 70 to 90 commands, although this will be less if commands that use a lot of memory are learned. • Remote controller buttons such as Play, Stop, Pause, and so on are preprogrammed with commands for controlling Onkyo CD players, cassette decks, and DVD players. However, they can learn new commands, and you can restore the preprogrammed commands at any time by resetting the remote controller (see page 138). • To overwrite a previously learned command, repeat this procedure. • Only commands from infrared remote controllers can be learned. • When the remote controller's batteries expire, all learned commands will be lost and will have to be learned all over again, so don't discard your other remote controllers.