Onkyo TXSR705 Owner Manual - Page 55

SETUP MIC jack.

Get Onkyo TXSR705 - 7.1 Channel Home Theater Receiver PDF manuals and user guides
UPC - 751398007804
View all Onkyo TXSR705 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

TX-SR705_En.book Page 55 Monday, May 28, 2007 2:13 PM First Time Setup-Continued 2 Put the speaker setup micro- 4 The speaker detect results phone at measurement point 1 appear. (page 54), and connect it to the Auto Speaker Setup AUDYSSEY SETUP MIC jack. - - - - - SP Detect Result - - - - - Auto Speaker Setup AUDYSSEY Please place microphone at center of listening area at ear height. FL : Yes SL : Yes SBL : Yes C : No Next Retry Cancel FR : Yes SR : Yes SBR : Yes SW : Yes Push Enter : Next Notes: • Make sure the microphone is hori- zontal. • If there's an obstacle between the microphone and any speaker, the automatic setup will not work correctly. Set up the room as you would when enjoying a DVD. • Positioning the microphone close to where your ears would normally be will provide better results. You can adjust the height of the microphone by using a tripod or level table. "Yes" means that the speaker was detected. "No" means that no speaker was detected. If you agree with the results, use the Up and Down [ ]/[ ] but- ENTER tons to select Next, and then press [ENTER]. The options are: Next: Proceed to the next step. ENTER Retry: Return to step 2 and try again. Cancel: Cancel the automatic speaker setup. 3 Press [ENTER]. 5 The following screen appears. The automatic speaker setup starts. Auto Speaker Setup AUDYSSEY Auto Speaker Setup AUDYSSEY Do not unplug microphone. Please place microphone at 2nd Position at ear height. Please keep quiet. Now Measuring. . . Push Enter : Next A test tone is output by each speaker in turn, as the Audyssey MultEQ XT function determines which speakers are connected. This takes a few minutes. Note: If any extraneous noise is picked up by the microphone, the automatic setup may not work correctly, so don't make any noise. Place the setup microphone at the next position (page 54), and then press [ENTER]. Audyssey MultEQ XT performs more measurements. This takes a few minutes. Auto Speaker Setup AUDYSSEY Do not unplug microphone. Please keep quiet. Now Measuring. . . 6 When prompted, place the setup microphone at the next position, and repeat step 5. 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
55
First Time Setup
—Continued
2
Put the speaker setup micro-
phone at measurement point
1
(page 54), and connect it to the
SETUP MIC jack.
Notes:
•
Make sure the microphone is hori-
zontal.
•
If there’s an obstacle between the
microphone and any speaker, the
automatic setup will not work cor-
rectly. Set up the room as you would
when enjoying a DVD.
•
Positioning the microphone close to
where your ears would normally be
will provide better results. You can
adjust the height of the microphone
by using a tripod or level table.
3
Press [ENTER].
The automatic speaker setup starts.
A test tone is output by each speaker in
turn, as the Audyssey MultEQ XT
function determines which speakers are
connected. This takes a few minutes.
Note:
If any extraneous noise is picked up by
the microphone, the automatic setup
may not work correctly, so don’t make
any noise.
Auto Speaker Setup
AUDYSSEY
Please place microphone at center
of listening area at ear height.
Push Enter : Next
Auto Speaker Setup
AUDYSSEY
Do not unplug microphone.
Please keep quiet.
Now Measuring. . .
4
The speaker detect results
appear.
“Yes” means that the speaker was
detected. “No” means that no speaker
was detected.
If you agree with the results, use
the Up and Down [
]/[
] but-
tons to select Next, and then
press [ENTER].
The options are:
Next
:
Proceed to the next step.
Retry
:
Return to step 2 and try again.
Cancel
:
Cancel the automatic speaker setup.
5
The following screen appears.
Place the setup microphone at
the next position (page 54), and
then press [ENTER].
Audyssey MultEQ XT performs more
measurements. This takes a few min-
utes.
6
When prompted, place the setup
microphone at the next position,
and repeat step 5.
Auto Speaker Setup
- - - - - SP Detect Result - - - - -
AUDYSSEY
Cancel
Retry
Next
:
Yes
:
Yes
:
Yes
:
No
:
Yes
:
Yes
:
Yes
:
Yes
FL
SL
SBL
C
FR
SR
SBR
SW
ENTER
ENTER
Auto Speaker Setup
AUDYSSEY
Please place microphone at
2nd Position at ear height.
Push Enter : Next
Auto Speaker Setup
AUDYSSEY
Do not unplug microphone.
Please keep quiet.
Now Measuring. . .
TX-SR705_En.book
Page 55
Monday, May 28, 2007
2:13 PM