Onkyo TXSR705 Owner Manual - Page 81

Speaker Level Calibration

Get Onkyo TXSR705 - 7.1 Channel Home Theater Receiver PDF manuals and user guides
UPC - 751398007804
View all Onkyo TXSR705 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 81 highlights

TX-SR705_En.book Page 81 Monday, May 28, 2007 2:13 PM Advanced Setup-Continued Speaker Level Calibration This setting is set automatically by the Automatic Speaker Setup function (see page 54). Here you can adjust the level of each speaker with the built-in test tone so that the volume of each speaker is the same at the listening position. Notes: • The speakers cannot be calibrated while the output of the AV receiver/AV amplifier is muted. • The test tone is output at the standard level for THX, which is 0 dB (absolute volume setting 82). If you normally listen at volume settings below this, be careful because the test tone will be much louder. 3 ENTER ENTER 2, 3 1, 6 1 2-5 4 ENTER Use the Up and Down [ ]/[ ] buttons to select "4. Level Calibration," and then press [ENTER]. The Level Calibration menu appears and the pink noise test tone is output by the front left speaker. 2-4. Level Calibration Left 0dB Center 0dB Right 0dB Surr Right 0dB Surr Back R 0dB Surr Back L 0dB Surr Left 0dB Subwoofer 0dB Note: Speakers that you set to No or None on the Speaker Configuration page (page 77) cannot be selected. Use the Up and Down [ ]/[ ] buttons to select each speaker, and use the Left and Right [ ]/ [ ] buttons to set the volume. The volume can be adjusted from -12 to +12 dB (-15 dB to +12 dB for the subwoofer) in 1 dB steps. 1 2 ENTER ENTER Press the [RECEIVER] button followed by the [SETUP] button. The main menu appears onscreen. Use the Up and Down [ ]/[ ] buttons to select "2. Speaker Setup," and then press [ENTER]. The Speaker Setup menu appears. 2. Speaker Setup 1. Speaker Settings 2. Speaker Config 3. Speaker Distance 4. Level Calibration 5. Equalizer Settings 6. THX Audio Setup ENTER 5 Repeat step 4 until the volume of the test tone from each speaker is the same. 6 Press the [SETUP] button. The setup menu closes. Notes: • This procedure can also be performed by using the [TEST TONE] button, [LEVEL-] and [LEVEL+] buttons. First press the [TEST TONE] button to output the test tone. Use the [LEVEL-] and [LEVEL+] buttons to set the volume, and use the [CH SEL] button to select the speakers. • This procedure can also be performed on the AV receiver/AV amplifier by using its [SETUP] button, arrow buttons, and [ENTER] button. 81

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
81
Advanced Setup
—Continued
Speaker Level Calibration
Here you can adjust the level of each speaker with the
built-in test tone so that the volume of each speaker is the
same at the listening position.
Notes:
•
The speakers cannot be calibrated while the output of
the AV receiver/AV amplifier is muted.
•
The test tone is output at the standard level for THX,
which is 0 dB (absolute volume setting 82). If you nor-
mally listen at volume settings below this, be careful
because the test tone will be much louder.
Notes:
•
This procedure can also be performed by using the
[TEST TONE] button, [LEVEL–] and [LEVEL+] but-
tons. First press the [TEST TONE] button to output
the test tone. Use the [LEVEL–] and [LEVEL+] but-
tons to set the volume, and use the [CH SEL] button to
select the speakers.
•
This procedure can also be performed on the AV
receiver/AV amplifier by using its [SETUP] button,
arrow buttons, and [ENTER] button.
1
Press the [RECEIVER] button fol-
lowed by the [SETUP] button.
The main menu appears onscreen.
2
Use the Up and Down [
]/[
]
buttons to select “2. Speaker
Setup,” and then press [ENTER].
The Speaker Setup menu appears.
This setting is set automatically by the Automatic
Speaker Setup function (see page 54).
2-5
1
2, 3
1, 6
ENTER
ENTER
2. Speaker Setup
1. Speaker Settings
2. Speaker Config
3. Speaker Distance
4. Level Calibration
5. Equalizer Settings
6. THX Audio Setup
3
Use the Up and Down [
]/[
]
buttons to select “4. Level Cali-
bration,” and then press
[ENTER].
The Level Calibration menu appears
and the pink noise test tone is output by
the front left speaker.
Note:
Speakers that you set to No or None on
the Speaker Configuration page
(page 77) cannot be selected.
4
Use the Up and Down [
]/[
]
buttons to select each speaker,
and use the Left and Right [
]/
[
] buttons to set the volume.
The volume can be adjusted from –12
to +12 dB (–15 dB to +12 dB for the
subwoofer) in 1 dB steps.
5
Repeat step 4 until the volume of
the test tone from each speaker
is the same.
6
Press the [SETUP] button.
The setup menu closes.
ENTER
ENTER
2–4. Level Calibration
Left
0dB
Center
0dB
Right
0dB
Surr Right
0dB
Surr Back R
0dB
Surr Back L
0dB
Surr Left
0dB
Subwoofer
0dB
ENTER
ENTER
TX-SR705_En.book
Page 81
Monday, May 28, 2007
2:13 PM