Optoma CinemaX P2 User Manual - Page 22

Powering off, Power, If you want the projector

Get Optoma CinemaX P2 PDF manuals and user guides View all Optoma CinemaX P2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

USING THE PROJECTOR Powering off 1. Turn off the projector by pressing the " " button either on top of the projector or on the remote control. The following message will be displayed: 2. 3. Note: ‡‡ ‡‡ ‡‡ The cooling fans will continue to operate for about 10 seconds for the cooling cycle and the power LED is flashing white. When the power LED turns red, this indicates the projector has entered standby mode. If you wish to turn the projector back on, you must wait until the cooling cycle has finished and the projector has entered standby mode. When the projector is in standby mode, simply press the " " button either on top of the projector or on the remote control again to turn on the projector. Disconnect the power cord from the electrical outlet and the projector. It is not recommended that the projector is turned on immediately, right after a power off procedure. By default, the projector turns off automatically after 20 minutes of inactivity. You can modify the idle time length in "Auto Power off (min.)" menu in "System Settings  Power". If you want the projector to enter sleep mode instead, disable auto power off and set the sleep time interval in "System Settings  Power Sleep Timer (min.)". To turn off the projector immediately, press the " " button twice either on top of the projector or on the remote control. 22 English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
English
22
USING THE PROJECTOR
Powering off
1.
Turn off the projector by pressing the “
” button either on top of the projector or on the remote control.
The following message will be displayed:
2.
The cooling fans will continue to operate for about 10 seconds for the cooling cycle and the power
LED is flashing white. When the power LED turns red, this indicates the projector has entered standby
mode. If you wish to turn the projector back on, you must wait until the cooling cycle has finished and
the projector has entered standby mode. When the projector is in standby mode, simply press the “
”
button either on top of the projector or on the remote control again to turn on the projector.
3.
Disconnect the power cord from the electrical outlet and the projector.
Note:
±
It is not recommended that the projector is turned on immediately, right after a power off procedure.
±
By default, the projector turns off automatically after 20 minutes of inactivity. You can modify the idle
time length in “Auto Power off (min.)” menu in “System Settings
Power”
.
If you want the projector to
enter sleep mode instead, disable auto power off and set the sleep time interval in “System Settings
Power
Sleep Timer (min.)”.
±
To turn off the projector immediately, press the “
” button twice either on top of the projector or on the
remote control.