Panasonic AJHD1700P AJHD1700 User Guide - Page 116

RACK MOUNTING, Attach the outer member brackets to the rack.

Get Panasonic AJHD1700P - HD VTR W/24P PDF manuals and user guides View all Panasonic AJHD1700P manuals
Add to My Manuals
Save this manual to your list of manuals

Page 116 highlights

Rack mounting The unit can be mounted into a 19-inch standard rack if the optional rack-mounting adapters (AJ-MA75P) are used. For the installation rails, it is recommended that the rail and bracket for 18-inch length (part number CC3061-99-0400) of Chassis Trak be used. If an even greater clearance is to be left between the VTR and rack when the VTR is pulled out, however, it is recommended that the 22-inch long Chassis Trak (part number CC-3001-99-0191) be used. (The complete slide rail and bracket unit is not available from Panasonic.) For further details, consult your dealer. 2 Attach the outer member brackets to the rack. Check that the height is the same for the left and right brackets. 3 Remove the four screws at the front used to attach the left and right side panels. 4 Attach the AJ-MA75P rack-mounting adapters using the same four screws. 1 Attach the inner members of the slide rails. Refer to the figure below for the positions where they are screwed into place. Positions where the right (R) inner member is screwed into place A BC DE F GH Inner member (18-inch rail) Rack-mounting adapters 5 Remove the four rubber feet on the bottom panel of the VTR, and install the VTR in the rack. After the VTR has been installed, check that it moves smoothly along the rails. EIA standard rack A BC DE F GH Inner member (22-inch rail) • The length of the screws used is subject to a restriction. • Use screws which are less than 2/5q (10 mm) long. • Attach the inner member at the same symmetrical positions on the left (L) side as well. Fix the members in place using 3 screws on each side (total: 6 screws). When using the 22-inch long slide rails, secure the screws at 4 locations. • The letters shown in the figure are not actually marked on the side panels. 116 Fasten to rack with the fixing screws. • Keep the temperature inside the rack to between 41xF and 104xF (5xC and 40xC). • Bolt the rack securely to the floor so that it will not topple over when the VTR is pulled out.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
116
A
B
C
D
E
F
G
H
2
Attach the outer member brackets to the rack.
Check that the height is the same for the left and
right brackets.
3
Remove the four screws at the front used to attach
the left and right side panels.
4
Attach the AJ-MA75P rack-mounting adapters
using the same four screws.
1
Attach the inner members of the slide rails.
Refer
to the figure below for the positions where they are
screwed into place.
The unit can be mounted into a 19-inch standard rack
if the optional rack-mounting adapters (AJ-MA75P)
are used. For the installation rails, it is recommended
that the rail and bracket for 18-inch length (part
number CC3061-99-0400) of Chassis Trak be used. If
an even greater clearance is to be left between the
VTR and rack when the VTR is pulled out, however, it
is recommended that the 22-inch long Chassis Trak
(part number CC-3001-99-0191) be used.
(The complete slide rail and bracket unit is not
available from Panasonic.)
For further details, consult your dealer.
Rack mounting
<Notes>
•
The length of the screws used is subject to a
restriction.
•
Use screws which are less than 2/5
q
(10 mm)
long.
•
Attach the inner member at the same symmetrical
positions on the left (L) side as well.
Fix the
members in place using 3 screws on each side
(total: 6 screws). When using the 22-inch long slide
rails, secure the screws at 4 locations.
•
The letters shown in the figure are not actually
marked on the side panels.
Inner member (18-inch rail)
A
B
C
D
E
F
G
H
Inner member (22-inch rail)
Positions where the right (R) inner
member is screwed into place
Rack-mounting adapters
5
Remove the four rubber feet on the bottom panel
of the VTR, and install the VTR in the rack.
After the VTR has been installed, check that it
moves smoothly along the rails.
EIA standard rack
Fasten to rack with the
fixing screws.
<CAUTIONS>
•
Keep the temperature inside the rack to between
41
x
F and 104
x
F (5
x
C and 40
x
C).
•
Bolt the rack securely to the floor so that it will not
topple over when the VTR is pulled out.