Panasonic AJHD1700P AJHD1700 User Guide - Page 88

Setup menus No./Item Description of setting No./Item Description of setting 300 IN/OUT DEL 301 NEGA FLASH For selecting the operation to be performed when an edit point has been set incorrectly (when the OUT point comes before the IN point). 0000 MANU: Editing is not performed unless the illegal edit point is cleared or set properly. 0001 AUTO: The edit point which had already been input is cleared automatically. For selecting whether to show a negative display (time code display area) when the IN point is greater than the OUT point. 0000 OFF: A negative display is not shown. 0001 ON: A negative display is shown. 302 CONFI EDIT For selecting whether to perform simultaneous playback during editing. 0000 OFF: Simultaneous playback is not performed. 0001 ON: Simultaneous playback is performed. Simultaneous playback takes effect when TAPE is selected as the F1 key OUTPUT setting on the menu. Refer to setup menu item No.140 as well. 303*1 AUD EDIT IN For selecting how to connect the digital audio edit IN points. 0000 CUT: Cut processing 0001 FADE: V-fade processing 304*1 AUD EDIT OUT For selecting how to connect the digital audio edit OUT points. 0000 CUT: Cut processing 0001 FADE: V-fade processing 305 AUTO ENTRY For selecting whether to register the IN points using the PREROLL button in cases where the IN points have not been registered. 0000 DIS: The IN points are not registered. 0001 ENA: The IN points are registered. 306*1 CF ADJ SEL For selecting the deck whose the color framing is to be adjusted during deck-to-deck editing. 0000 PLAYER: The player's IN and OUT points are adjusted (using the recorder as the reference). 0001 RECORD: The recorder's IN and OUT points are adjusted (using the player as the reference). 307 AFTER CUE-UP For selecting the VTR's mode upon completion of the cue-up operation. 0000 STOP: The VTR is set to the STOP mode. 0001 STILL: The VTR is set to the still picture (SHTL STILL) mode. 0002 STILL2: The VTR is set to the still picture (VAR STILL) mode. 308 VAR FWD MAX For setting the maximum speed of VAR FWD. 0000 i4.9: i4.9 times normal tape speed 0001 i2: i2 times normal tape speed (i1.85 times normal tape speed for formats other than DVCPRO HD-LP) 0002 i1: i1 times normal tape speed • At any setting other than 0 (i4.9), phase adjustments cannot be conducted from the editing controller. • Depending on the format used, the actual tape running speed differs slightly from what is indicated by the superimposed display. 309 VAR REV MAX For setting the maximum speed of VAR REV. 0000 j4.9: j4.9 times normal tape speed 0001 j2: j2 times normal tape speed (j1.85 times normal tape speed for formats other than DVCPRO HD-LP) 0002 j1: j1 times normal tape speed Depending on the format used, the actual tape running speed differs slightly from what is indicated by the superimposed display. 310 JOG FWD MAX For setting the maximum speed of JOG FWD. 0000 i4.9: i4.9 times normal tape speed 0001 i2: i2 times normal tape speed (i1.85 times normal tape speed for formats other than DVCPRO HD-LP) 0002 i1: i1 times normal tape speed At any setting other than 0 (i4.9), phase adjustments cannot be conducted from the editing controller which performs these adjustments by the JOG command. 311 For setting the maximum speed of JOG REV. 0000 j4.9: j4.9 times normal tape speed JOG REV MAX 0001 j2: j2 times normal tape speed (j1.85 times normal tape speed for formats other than DVCPRO HD-LP) 0002 j1: j1 times normal tape speed 312 POSTROLL TM For setting the postroll time. Any time from 0 to 5 seconds can be set in 1- second increments. 0000 0s 0001 1s 0002 2s 0003 3s 0004 4s 0005 5s *1: This item is not displayed when the 23/24 Hz or 25 Hz (HD or SD) mode has been selected as the system menu item No.25 (SYSTEM FREQ) setting. The underlining (__) denotes the factory setting mode. 88