Panasonic AJHD1700P AJHD1700 User Guide - Page 19

Parts and Their Functions Rear panel AC IN SIGN L GD > DBH TC PUSH CUE PUSH MON IN IN L OUT OUT R HD SDI IN OUT 1 OUT 2 OUT 3 MONITOR (SUPER) ACTIVE THROUGH SDTI SD SDI AUDIO IN CH1·2 CH3·4 CH5·6 CH7·8 IN (OPTION) AUDIO CH1·2 OUT CH3·4 CH5·6 CH7·8 CH 1 PUSH AUDIO IN CH 2 PUSH CH 3 PUSH OUT CH 4 PUSH CH 1 CH 2 AUDIO OUT CH 3 CH 4 MONITOR (SUPER) DIGITAL AUDIO ANALOG VIDEO OUT SD REF IN 1 HD REF IN HD REF OUT PARALLEL 2 (WFM) ON 75≠ OFF ON 75≠ OFF ENCODER REMOTE 3 (SUPER) SD REF OUT R E RS-232C M O T E REMOTE IN/OUT REMOTE OUT ? @ AC G F E > SD SERIAL DIGITAL COMPONENT AUDIO and VIDEO OUT connectors The digital component audio and video signals complying with the SMPTE 259M-C, 272M-A or 294M standard are output from these connectors. They are output during DVCPRO25M, 50M, DV or DVCAM interchangeable playback or when signals are down-converted and output. Signals containing TC, menu or other superimposed information can be output from the SD SDI MONITOR. Using setup menu item No.606 (SD MONI O SEL), it is also possible to make the SD SDI MONITOR output the same output as SD SDI OUT1 (no information superimposed). When "SD SDI" has been selected as the F1 (VID IN) setting on the menu and "THRU" has been selected as the No.107 (EE MODE SEL) setting, no information is superimposed onto the SD SDI MONITOR output signals in the EE mode, and the same output as SD SDI OUT1 is delivered. • The AJ-UC1700G optional board is required in order to select "SD SDI" as the F1 (VID IN) setting on the menu. • For INPUT CHECK, refer to the INPUT CHECK output table on page 15. Note that the signals are muted during line conversion. In the 23/24 Hz mode, the system phase of the SD SDI output and analog composite video output is subject to change when the tape has been set to travel at the normal speed (1k) so that the HD SDI output and phase will be aligned. ? ANALOG COMPOSITE VIDEO OUT connectors The analog composite video signals are output through these connectors. They are output during DVCPRO25M, 50M, DV or DVCAM interchangeable playback or when signals are down-converted and output. Video signals containing superimposed information can be output through the VIDEO OUT 3 connector. Whether the superimposing is to be set ON or OFF is selected using the setup menu item No.005 (SUPER). The waveform monitor (WFM) signal can be output from the VIDEO OUT 2 connector. The signals which can be switched using the menu items are the TC, CTL, video, RF L/R and ENV L/R signals. There is no INPUT CHECK function. The signals are muted during line conversion. @ SD REF IN connectors and 75-ohm termination switches These are the SD reference video signal input connectors. Input composite signal with color burst. For termination, set the termination switch to ON. A HD REF IN connectors and 75-ohm termination switches These are the HD reference video signal input connectors. Input tri-level sync signals with both positive and negative polarities. For termination, set the termination switch to ON. B HD REF OUT connector This is the HD reference video signal output connector for external synchronization. Tri-level sync signals with both positive and negative polarities are output. The output based on SYS FORMAT of menu item No.020 is delivered from the connector. C SD REF OUT connector The composite signal used for external synchronization (black burst signal) is output from this connector. D DIGITAL AUDIO IN and OUT connectors These are the input and output connectors of the digital audio signals that comply with the AES/EBU standards. E Remote control connectors These connectors make it possible to use two of these VTRs or to connect this VTR to an external controller so that this VTR can be operated from an external component. Two remote control connectors are provided: one for IN/OUT uses and the other for OUT uses only. IN/OUT:For connection with an external controller For connection during deck-to-deck operations OUT: For connection during parallel run operations For loop-through uses F ENCODER REMOTE connector An external encoder remote controller is connected to this connector when the video output signal settings are to be adjusted from an external component. G RS-232C connector H PARALLEL REMOTE connector This is used when the VTR is to be operated from an external component. 19