Panasonic PTDS8500U PTDS8500U User Guide - Page 39

Powering up the projector, Making adjustment and selection, Press POWER ON | .

Get Panasonic PTDS8500U - DLP PROJECTOR PDF manuals and user guides
UPC - 885170010994
View all Panasonic PTDS8500U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Basic Operation Powering ON/OFF 3) 5) 4) 8), 10), 11), 12) 3) 5) 4), 11) 9) 6) 8) 10), 12) 1) 2) 7) 6) 9) Powering up the projector When using an optional lens, install a projection lens before switch on the projector. (Æpage 37) Remove the projection lens cover from the lens. 1111 Connect the supplied power cable. (AC120 V 60 Hz) 2222 Press the [ | ] marked side of the MAIN POWER switch to turn on the power. The POWER indicator lamp on the projector will flash in red. After a short period, the indicator will illuminate and the projector will enter standby mode. 3333 Press POWER ON ( | ). [Power indicator] lamp illuminates in green and soon the image is projected on the screen. Note zzIf the projector is powered up at about 0 °C, a warm-up period of approximately 5 minutes may be necessary to start projection. indicator lamp lights up during the warm-up period. When the warm-up is completed, indicator lamp turns off and the image is projected on the screen. zzIf the temperature of the operating environment is low and warm-up takes more than 5 minutes, the projector will judge that a problem has occurred and the power will be turned off automatically. If this happens, increase the temperature around the projector so that it is 0 °C or higher, and then turn on the MAIN POWER switch and the POWER ON ( | ) switch once more. zzWith [ECO] setting in [Standby mode] (Æpage 81), When switch on the projector, projection will start about 10 seconds late. zzIf the filter is not installed, the power is turned off automatically after 10 minutes. zzIf projection was stopped last time by using the DIRECT POWER OFF function, it can be started by setting the MAIN POWER switch to the " I " (ON) position. Making adjustment and selection It is recommended that the images are projected continuously for at least 30 minutes before the focus is adjusted. 4444 Press button, roughly adjust the focus of the lens. (Æpage 41) 5555 Select and set the projection scheme of [INSTALLATION] and [COOLING CONDITION] settings in [PROJECTOR SETUP] menu. 6666 Select the input signal by pressing button (, , , , ). (SDI: PT-DZ8700U/ PT-DS8500U only) 7777 Adjust the tilt of the main unit in front and rear or right and left. 8888 Press button to adjust the position of the projection. 9999 Press button if the input signal is RGB signal. 1111 Zoom the lens so the image fills the screen. 1111 Readjust the focus. 1111 Readjust the zoom so that the image size fits in the screen. ENGLISH - 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
Powering ON/OFF
ENGLISH -
39
Basic Operation
Powering up the projector
When using an optional lens, install a projection lens
before switch on the projector. (
Æ
page 37)
Remove the projection lens cover from the lens.
Connect the supplied power cable.
1 )
(AC120 V 60 Hz)
Press the [ | ] marked side of the
2 )
MAIN POWER switch to turn on the
power.
The POWER indicator lamp on the projector will
flash in red. After a short period, the indicator will
illuminate and the projector will enter standby
mode.
Press POWER ON ( | ).
3 )
[Power indicator] lamp illuminates in green and
soon the image is projected on the screen.
Note
If the projector is powered up at about 0 °C, a warm-up
z
period of approximately 5 minutes may be necessary to
start projection. <TEMP> indicator lamp lights up during
the warm-up period. When the warm-up is completed,
<TEMP> indicator lamp turns off and the image is
projected on the screen.
If the temperature of the operating environment is low
z
and warm-up takes more than 5 minutes, the projector
will judge that a problem has occurred and the power
will be turned off automatically. If this happens, increase
the temperature around the projector so that it is 0 °C or
higher, and then turn on the MAIN POWER switch and
the POWER ON ( | ) switch once more.
With [ECO] setting in [Standby mode]
z
(
Æ
page 81), When
switch on the projector, projection will start about 10
seconds late.
If the filter is not installed, the power is turned off
z
automatically after 10 minutes.
If projection was stopped last time by using the DIRECT
z
POWER OFF function, it can be started by setting the
MAIN POWER switch to the “ I ” (ON) position.
Making adjustment and
selection
It is recommended that the images are projected
continuously for at least 30 minutes before the focus
is adjusted.
Press <FOCUS> button, roughly
4 )
adjust the focus of the lens.
(
Æ
page 41)
Select and set the projection scheme
5 )
of [INSTALLATION] and [COOLING
CONDITION] settings in [PROJECTOR
SETUP] menu.
Select the input signal by pressing
6 )
<INPUT SELECT> button (<RGB1>,
<RGB2>, <DVI-D/HDMI>, <VIDEO>
<S-VIDEO>, <SDI>).
(SDI: PT-DZ8700U/ PT-DS8500U only)
Adjust the tilt of the main unit in front
7 )
and rear or right and left.
Press <SHIFT> button to adjust the
8 )
position of the projection.
Press <AUTO SETUP> button if the
9 )
input signal is RGB signal.
Zoom the lens so the image fills the
10)
screen.
Readjust the focus.
11)
Readjust the zoom so that the image
12)
size fits in the screen.
2)
1)
7)
6)
9)
3)
5)
4)
8), 10), 11), 12)
9)
3)
5)
4), 11)
8)
6)
10), 12)