Panasonic PTDS8500U PTDS8500U User Guide - Page 60

CLOCK PHASE, GEOMETRY (PT-DZ8700/PT-DS8500 only), Press ▲▼ to select [CLOCK PHASE]. - pt ds8500

Get Panasonic PTDS8500U - DLP PROJECTOR PDF manuals and user guides
UPC - 885170010994
View all Panasonic PTDS8500U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

POSITION menu 3333 Press ▲▼ to select [INTERLOCKED]. 4444 Press ◄► to switch [INTERLOCKED]. OFF ON The [VERTICAL] and [HORIZONTAL] settings are used as the vertical and horizontal zoom ratios respectively. The zoom ratio is set to the [BOTH] setting. This allows the pictures to be zoomed at equal vertical and horizontal ratios. Note zzWhen [ASPECT] is set to [THROUGH], [ZOOM] will not appear. zzWhen other than [DEFAULT] is selected for [ASPECT], the [MODE] selection setting will not appear. CLOCK PHASE Clock phase adjustment achieves the best image when the screen flickers or halos are observed around contours. 1111 Press ▲▼ to select [CLOCK PHASE]. 2222 Press ◄► or button. zzThe [CLOCK PHASE] individual adjustment screen will be displayed. 3333 Press ◄► to adjust the level. zzThe value changes from 0 to 63. Adjust so that the amount of interference is at a minimum. Note zzThe CLOCK PHASE may not be adjusted, depending on the signal. zzNo optimal value may be obtained if the output of the PC to which the signal input is applied is unstable. zzNo optimal value may be obtained if the total number of dots is not correct. zzThe [CLOCK PHASE] can be adjusted only when RGB signal input is applied with RGB1 and RGB2 IN. GEOMETRY (PT-DZ8700/PT-DS8500 only) Square video can be projected onto a special shaped screen using unique image processing technology. 1111 Press ▲▼ to select [GEOMETRY]. 2222 Press ◄► to switch [GEOMETRY]. zzThe setting will change as follows each time ◄► is pressed. OFF KEYSTONE PC CURVED OFF KEYSTONE CURVED PC Û Geometry correction is not performed. This adjusts projected images when they are distorted to a trapezoid. This adjusts projected images when they are distorted to a curved surface. This is for performing geometry correction from a computer. ½½½ GEOMETRY adjustment should be carried out by a person who is familiar with the projector or by a service person because a high level of skill is required to make successful adjustment. 3333 Select [KEYSTONE] or [CURVED] in Step 2), and press button. zzThe [GEOMETRY : KEYSTONE] or [GEOMETRY : CURVED] screen will be displayed. 4444 Press ▲▼ to select the desired adjustment item, and press ◄► to adjust the correction amount. zzYou can adjust the projection images as shown below. Settings 60 - ENGLISH

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
POSITION menu
60
- ENGLISH
Settings
Press ▲▼ to select [INTERLOCKED].
3 )
Press ◄► to switch [INTERLOCKED].
4 )
OFF
The [VERTICAL] and
[HORIZONTAL] settings are used
as the vertical and horizontal zoom
ratios respectively.
ON
The zoom ratio is set to the [BOTH]
setting.
This allows the pictures to be
zoomed at equal vertical and
horizontal ratios.
Note
When [ASPECT] is set to [THROUGH], [ZOOM] will not
z
appear.
When other than [DEFAULT] is selected for [ASPECT],
z
the [MODE] selection setting will not appear.
CLOCK PHASE
Clock phase adjustment achieves the best image
when the screen flickers or halos are observed around
contours.
Press ▲▼ to select [CLOCK PHASE].
1 )
Press ◄► or <ENTER> button.
2 )
The [CLOCK PHASE] individual adjustment
z
screen will be displayed.
Press ◄► to adjust the level.
3 )
The value changes from 0 to 63. Adjust so that
z
the amount of interference is at a minimum.
Note
The CLOCK PHASE may not be adjusted, depending on
z
the signal.
No optimal value may be obtained if the output of the PC
z
to which the signal input is applied is unstable.
No optimal value may be obtained if the total number of
z
dots is not correct.
The [CLOCK PHASE] can be adjusted only when RGB
z
signal input is applied with RGB1 and RGB2 IN.
GEOMETRY
(PT-DZ8700/PT-DS8500 only)
Square video can be projected onto a special shaped
screen using unique image processing technology.
Press ▲▼ to select [GEOMETRY].
1 )
Press ◄► to switch [GEOMETRY].
2 )
The setting will change as follows each time
z
◄► is pressed.
OFF
KEYSTONE
PC
CURVED
OFF
Geometry correction is not
performed.
KEYSTONE
This adjusts projected images when
they are distorted to a trapezoid.
CURVED
This adjusts projected images
when they are distorted to a curved
surface.
PC
Û
This is for performing geometry
correction from a computer.
GEOMETRY adjustment should be carried out by
:
Û
a person who is familiar with the projector or by
a service person because a high level of skill is
required to make successful adjustment.
Select [KEYSTONE] or [CURVED] in
3 )
Step 2), and press <ENTER> button.
The [GEOMETRY : KEYSTONE] or
z
[GEOMETRY : CURVED] screen will be
displayed.
Press ▲▼ to select the desired
4 )
adjustment item, and press ◄► to
adjust the correction amount.
You can adjust the projection images as shown
z
below.