Pioneer VSX-47TX Owner's Manual - Page 111

Techno Tidbits & Problem-solving Specifications Amplifier Section Continuous average power output of 160 watts* per channel, min., at 6 ohms, from 20 Hz to 20,000 Hz with no more than 0.09 %** total harmonic distortion (front). Continuous Power Output (6 Ω) Front ....... 160 W + 160 W (20 Hz-20 kHz, 0.09 %, 6 Ω) Center 160 W (20 Hz-20 kHz, 0.09 %, 6 Ω) Surround ..... 160 W + 160 W (20 Hz-20 kHz, 0.09 %, 6 Ω) Surr. back .... 160 W + 160 W (20 Hz-20 kHz, 0.09 %, 6 Ω) Continuous Power Output ( 8 Ω) Front ....... 130 W + 130 W (20 Hz-20 kHz, 0.09 %, 8 Ω) Center 130 W (20 Hz-20 kHz, 0.09 %, 8 Ω) Surround 130 W + 130 W (20 Hz-20 kHz, 0.09 %, 8 Ω) Surr. back .......... 130 W + 130 W (20 Hz-20 kHz, 0.09 %, 8 Ω) Audio Section Input (Sensitivity/Impedance) PHONO MM 4.7 mV/47 kΩ LINE 382 mV/47 kΩ Phono Overload level (T.H.D.0.1 %, 1kHz) PHONO MM 120 mV Frequency Response PHONO MM 20 Hz to 20,000 Hz ± 0.3 dB LINE 5 Hz to 100,000 Hz +0 -3 dB Output (Level/Impedance) LINE 382 mV/2.2 kΩ Tone Control BASS 6 dB (100 Hz) TREBLE 6 dB (10 kHz) LOUDNESS 4/+2 dB (100Hz/10 kHz) (at volume position -40dB) Signal-to-Noise Ratio (IHF, short circuited, A network) PHONO MM 86 dB LINE 105 dB Video Section Input (Sensitivity 1 Vp-p/75 Ω Output (Level/Impedance 1 Vp-p/75 Ω Signal-to-Noise Ratio 70 dB Frequency Response 5 Hz to 10 MHz dB Component Video Section Input (Sensitivity 1 Vp-p/75 Ω Output (Level/Impedance 1 Vp-p/75 Ω Signal-to-Noise Ratio 70 dB Frequency Response 5 Hz to 40 MHz +-30dB FM Tuner Section Frequency Range 87.5 MHz to 108 MHz Usable Sensitivity ........ Mono: 13.2 dBf, IHF (1.3 µV/75 Ω) 50 dB Quieting Sensitivity Mono: 20.2 dBf Stereo: 38.6 dBf Signal-to-Noise Ratio Mono: 73 dB (at 85 dBf) Stereo: 70 dB (at 85 dBf) Distortion Stereo: 0.5 % (1 kHz) Alternate Channel Selectivity 60 dB (400 kHz) Stereo Separation 40 dB (1 kHz) Frequency Response 30 Hz to 15 kHz (± 1) dB Antenna Input 75 Ω unbalanced AM Tuner Section Frequency Range 530 kHz to 1,700 kHz Sensitivity (IHF, Loop antenna 350 µV/m Selectivity 25 dB Signal-to-Noise Ratio 50 dB Antenna Loop antenna Miscellaneous Power Requirements AC 120 V, 60 Hz Power Consumption 710 W Power Consumption in Standby mode 0.65 W AC Outlet SWITCHED 100 W (0.8 A) MAX Dimensions 440 (W) × 203 (H) × 472 (D) mm (17-5/16 (W) × 8 (H) × 18-9/16 (D) in.) Weight (without package 28.3 kg (62 lb 4 oz) Signal-to-Noise Ratio [EIA, at 1 W (1 kHz)] PHONO MM 83 dB LINE 93 dB * Measured pursuant to the Federal Trade Commission's Trade Regulation rule on Power Output Claims for Amplifiers. ** Measured by Audio Spectrum Analyzer. Furnished Parts FM wire Antenna 1 AM Loop Antenna 1 "AA" IEC LR6 batteries 4 Remote Control Unit 1 Remote Control Cable 1 Remote Control Stand 1 U-shaped connectors 2 AC Power Cord 1 Operating Instructions 1 Maintenance of External Surfaces • Use a polishing cloth or dry cloth to wipe off dust and dirt. • When the surfaces are dirty, wipe with a soft cloth dipped in some neutral cleanser diluted five or six times with water, and wrung out well, and then wipe again with a dry cloth. Do not use furniture wax or cleaners. • Never use thinners, benzine, insecticide sprays or other chemicals on or near this unit, since these will corrode the surfaces. NOTE: Specifications and the design are subject to possible modifications without notice, due to improvements. 111 EXPERT