Pioneer VSX-47TX Owner's Manual - Page 14

be prepared for loud test tones.

Page 14 highlights

Quick Start Guide Part2 10 1. Auto Surround Setup Connect microphone Please be quiet Move obstacles away If you have a subwoofer turn power on and turn volume up [Start] [Cancel] \ 1. Auto Surround Setup Please Wait Caution!! Test tone is output loudly. [Cancel] \ Auto Surround Setup Now Analyzing••• Environment Check Ambient Noise Microphone Speaker Level [OK] [OK] [OK] [Cancel] \ 11 1. Auto Surround Setup Front [ YES ] Center [ YES ] Surround [ YES ] SurrBack [ NO ] Subwoofer [ NO ] [OK] [Retry] [ERR Fix SP.] [Return to Menu] Auto Surround Setup Now Analyzing••• Surround Analysis Speaker Systems Channel Delay Channel Level Acoustic Cal EQ [OK] [OK] [OK] [OK] [Cancel] Speaker Systems Check " Normal Surround " Front Center Surround SurrBack Subwoofer [SMALL] [SMALL] [SMALL] [SMALLX2] [ YES ] [Next] ( Back/Next ) [Return] 14 9 Some auto setup instructions will be listed, make sure to follow them. Make sure you have: hooked up the remote control microphone and moved obstacles to the speakers out of the way. If you have a subwoofer make sure it is turned on and has the volume turned up. WARNING: The test tones are very loud!! Make sure there are no infants or small children in the room and that no one who will be scared, upset or injured by loud noise is present. You yourself may want to wear earplugs. It is possible to lower the volume of test tones, but this could result in incorrect speaker settings. 10 If you have followed all setup instructions and warnings above make sure that the arrow is pointed to START and press ENTER. Put the remote control into the its stand and be prepared for loud test tones. Try to be as quiet as possible after hitting ENTER. The test tones may take up to 30 seconds. The volume automatically increases to 0dB, then the system will output some test tones and establish ambient noise levels, the microphone status, and what speakers you hooked up. 11 Check the speaker settings on the OSD If they match your speaker configuration make sure OK,GO NEXT is selected and press ENTER. Put the remote control into the its stand again. The test tones will be output loudly again. The test tones may take up to 5 minutes this time. After it has finished, you see the SPEAKER SYSTEMS CHECK screen. If you want to view the settings select NEXT and press ENTER repeatedly. If not, simply go to step 13. If they do not match the speaker configuration you hooked up and you wan to try again select RETRY with 5∞ buttons and press ENTER. Put the remote control into the its stand again. Follow the instructions above from step 10. If the speaker settings do not match the speaker configuration you connected and you want to input the settings manually select ERR=FIX SP with the 5∞ buttons, press ENTER. Put the remote control into the its stand again. and go to step 12. If you see an ERR message in the right side column, there may be a problem with the speaker connection. If selecting RETRY doesn't fix the problem, turn off the power and check the speaker connections. 12 Use the ∞5 buttons to select a speaker then the 2 3 buttons to select the size of each speaker individually.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112

14
Quick Start Guide
Part2
9
Some auto setup instructions will be
listed, make sure to follow them.
Make sure you have: hooked up the remote control
microphone and moved obstacles to the speakers out of
the way. If you have a subwoofer make sure it is turned
on and has the volume turned up.
WARNING:
The test tones are very loud!! Make sure
there are no infants or small children in the room and
that no one who will be scared, upset or injured by loud
noise is present. You yourself may want to wear ear-
plugs. It is possible to lower the volume of test tones,
but this could result in incorrect speaker settings.
10
If you have followed all setup
instructions and warnings above make
sure that the arrow is pointed to
START and press ENTER. Put the
remote control into the its stand and
be prepared for loud test tones.
Try to be as quiet as possible after hitting ENTER. The
test tones may take up to 30 seconds.
The volume automatically increases to 0dB, then the
system will output some test tones and establish
ambient noise levels, the microphone status, and what
speakers you hooked up.
11
Check the speaker settings on the OSD
If they match your speaker configuration make sure
OK,GO NEXT
is selected and press
ENTER
. Put the
remote control into the its stand again. The test tones
will be output loudly again. The test tones may take up
to 5 minutes this time.
After it has finished, you see the SPEAKER
SYSTEMS CHECK screen. If you want to view the
settings select
NEXT
and press
ENTER
repeatedly. If
not, simply go to step 13.
If they do not match the speaker configuration you
hooked up and you wan to try again select
RETRY
with
5∞
buttons and press
ENTER
. Put the remote control
into the its stand again. Follow the instructions above
from step 10.
If the speaker settings do not match the speaker
configuration you connected and you want to input the
settings manually select
ERR
=
FIX SP
with the
5∞
buttons, press
ENTER
. Put the remote control into the
its stand again. and go to step 12.
If you see an ERR message in the right side column,
there may be a problem with the speaker connection. If
selecting RETRY doesn't fix the problem, turn off the
power and check the speaker connections.
12
Use the
∞5
buttons to select a speaker
then the
2
3
buttons to select the size
of each speaker individually.
10
1. Auto
Surround
Setup
Please
Wait
Caution!!
Test
tone
is
output
loudly.
[
Cancel
]
1. Auto Surround
Setup
Connect
microphone
Please
be
quiet
Move
obstacles
away
If
you
have
a
subwoofer
turn
power
on
and
turn
volume
up
[
Start
]
[Cancel]
Auto
Surround
Setup
Now
Analyzing
•••
Environment
Check
Ambient
Noise
[OK]
Microphone
[OK]
Speaker
Level
[
OK
]
[
Cancel
]
1. Auto Surround
Setup
Front
[ YES ]
Center
[ YES ]
Surround
[ YES ]
SurrBack
[
NO
]
Subwoofer
[ NO
]
[
OK
]
[Retry]
[ERR
Fix
SP.]
[Return
to
Menu]
11
\
\
Auto Surround Setup
Now
Analyzing
•••
Surround
Analysis
Speaker
Systems
[OK]
Channel
Delay
[
OK
]
Channel
Level
[
OK
]
Acoustic
Cal
EQ
[
OK
]
[
Cancel
]
Speaker
Systems Check
Normal
Surround
Front
[SMALL]
Center
[SMALL]
Surround
[SMALL]
SurrBack
[SMALL
X
2]
Subwoofer
[
YES
]
[
Next
]
(
Back/Next
)
[Return]
\