Sharp DV-HR300U DV-HR300U Operation Manual - Page 90

Editing a Play List (HDD/DVD) 5 Adding a Title or Chap- ter 1 Select "ADD CHAPTER/TITLE", then press SET/ENTER. 2 Select a title (chapter) at the title (chapter) list, then press SET/ENTER. Go to step 9. Specifying and Adding a Scene • Select "SPECIFY SCENE TO ADD", then press SET/ENTER. Go to step 6. EDIT(HDD PLAYLIST) TITLE: CH33 FINE 12 / 25 SAT 10 : 28 AM TITLE INFO: 10/4 MON 8:09 PM - 8:14 PM ERASE SCENE CHANGE TITLE NAME CHANGE THUMBNAIL DIVIDE CHAPTER ADD CHAPTER/TITLE SELECT ORIGINAL TITLE/CHAPTER AND ADD IT ADD SCENE MOVE TITLE SPECIFY SCENE TO ADD SELECT A SCENE FROM ORIGINAL VIDEO AND ADD IT SELECT ENTER ENTER n RETURN 6 Press to select title (chapter) to edit, then press SET/ ENTER. •The selected title (chapter) pauses. EDIT(HDD ORIGINAL) TITLE: CH33 FINE TITLE INFO: 10/4 MON 8:09 PM - 8:14 PM ERASE SCENE CHANGE TITLE NAME CHANGE THUMBNAIL DIVIDE CHAPTER ADD SCENE MOVE TITLE 12 / 25 SAT 10 : 28 AM 2 01 00: 00: 00 04 SPECIFY RANGE TO ADD PLAY PLAYBACK ENTER SET START POINT 7 1 Press |PLAY to start playback. •Find the scene to add using FSTILL/ PAUSE, JFWD, GREV, K, L, or SLOW. EDIT(HDD ORIGINAL) TITLE: CH33 FINE TITLE INFO: 10/4 MON 8:09 PM - 8:14 PM ERASE SCENE CHANGE TITLE NAME CHANGE THUMBNAIL DIVIDE CHAPTER ADD SCENE MOVE TITLE 12 / 25 SAT 10 : 28 AM 2 01 00: 00:12 00 SPECIFY RANGE TO ADD PLAY PLAYBACK ENTER SET START POINT 2 Press SET/ENTER at the start point of the scene you want to add. ERASE SCENE CHANGE TITLE NAME CHANGE THUMBNAIL DIVIDE CHAPTER ADD SCENE MOVE TITLE 2 01 00:00: 32 09 SPECIFY RANGE TO ADD PLAY PLAYBACK ENTER SET END POINT •If you fast reverse to a scene prior to the start point, the start point will be canceled. •When the start point is set to near the beginning of a chapter, the beginning of the chapter will be selected as the start point. To make the original designated start point effective, set it again after combining up with the chapter just before. (page 86) 8 Press SET/ENTER at the end of the scene you want to add. •Press RETURN to reselect the start point of the scene. You can press RETURN to reselect the end point even after it is already set. ERASE SCENE CHANGE TITLE NAME CHANGE THUMBNAIL DIVIDE CHAPTER ADD SCENE MOVE TITLE 2 01 00:00: 32 09 CONFIRM CONTENT? n RETURN CONFIRMING ADD •When the end point is set to near the end of a chapter, the end of the chapter will be selected as the end point. To make the original designated end point effective, set it again after combining up with the chapter just before. (page 86) 9 Press Red (B) (CONFIRMING) to confirm the content. Press Yellow (D) (ADD) to add. •If you press Red (B) (CONFIRMING), you can test play the added scene, from the start point to the end point. It may take about one minute for the confirm screen to appear. •Press Yellow (D) (ADD) to add. 10 1 Press \ / | to select "YES". 2 Press SET/ENTER. •The scene is added after the selected title, and stored as a new title of the play list. 11 Press EXIT to exit from EDIT mode. •A chapter mark is automatically set at the start point where the scene is added. NOTE •When adding a scene, select a scene which continues for at least 3 seconds. Scenes shorter than 3 seconds cannot be added. •Scenes can only be added and erased a maximum of 50 times per title. •If you press G REV or Kand reverse beyond the start point after setting a start point, the start point will cancel. •If scenes have been added or erased 51 or more times to a single title in a disc using another DVD recorder, Editing (Recording) may not function. 90