Sharp MX-C303W MX-C303W MX-C304W Troubleshooting Guide - Page 38

Transmission Does Not Take Place

Page 38 highlights

Fax Problems ? Problem NOTIFICATION SOUNDS ARE TOO LOUD OR TOO SOFT, OR ARE NOT AUDIBLE (VOLUME ADJUSTMENT) I DON'T KNOW HOW TO STORE OR PRINT SENDER INFORMATION BROADCAST TRANSMISSION DOES NOT WORK THE DATA NOTIFICATION INDICATOR DOES NOT TURN OFF I DON'T KNOW HOW TO CHECK AN ADDRESS WHEN SENDING A FAX Check Have you adjusted the volume in the speaker settings of setting mode? You can adjust the volume of the original scan complete sound in the scan complete sound setting of setting mode. You can store sender information in "Own Name and Destination Set" in setting mode. Has broadcast setting been disabled in the setting mode (administrator)? Is an error preventing received faxes from being printed? Tap the [Address Review] key. Is "Fax Dest. Confirmation Mode" enabled in setting mode? Page 45 45 45 45 46 46 46 ? TRANSMISSION DOES NOT TAKE PLACE Check Is the telephone line connected securely? Is the correct dial mode set for your line? Is a busy signal received? Did a communication error occur? Does a message appear indicating that the memory is full? ! Solution ■ Check the telephone line jack, the wall jack, and any extension adapters to make sure that all connections are secure. ► Power and connector positions (page 4) ■ Ask your administrator to verify that "Dial Mode Setting" is set correctly for the line you are using. Select the telephone line type in "Dial Mode Setting" in the setting mode (administrator).  "Settings" → [System Settings] → [Image Send Settings] → [Fax Settings] → [Condition Settings] → [Dial Mode Setting] ■ If a busy signal is received, the transmission is temporarily canceled and then automatically attempted again after a brief interval. The factory default setting : Two attempts at 3-minute intervals.  "Settings" → [System Settings] → [Image Send Settings] → [Fax Settings] → [Send Setting] → [Recall in Case of Line Busy] To cancel transmission, tap the job status display on the operation panel, tap the key of the job you want to delete, and tap [Stop/Delete] on the action panel. A message will appear to confirm the cancelation. Tap the [Cancel] key. ■ If an error occurs preventing transmission, the transmission is temporarily canceled and then automatically re-attempted after a brief interval. The factory default setting : Two attempts at 3-minute intervals.  "Settings (administrator)" → [System Settings] → [Image Send Settings] → [Fax Settings] → [Send Setting] → [Recall in Case of Communication Error] To cancel transmission, tap the job status display on the operation panel, tap the key of the job you want to delete, and tap [Stop/Delete] on the action panel. A message will appear to confirm the cancelation. Tap the [Cancel] key. The machine supports error correction mode (ECM) and is configured to automatically resend any part of a fax that is distorted due to noise on the line.  "Settings" → [System Settings] → [Image Send Settings] → [Fax Settings] → [Default Settings] → [ECM] ■ Divide the originals into sets and fax each set separately, or use direct transmission. If the memory becomes full, the transmission will be canceled. 38

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66

38
Fax Problems
NOTIFICATION SOUNDS ARE TOO
LOUD OR TOO SOFT, OR ARE NOT
AUDIBLE (VOLUME ADJUSTMENT)
Have you adjusted the volume in the speaker settings of setting mode?
45
You can adjust the volume of the original scan complete sound in the
scan complete sound setting of setting mode.
45
I DON'T KNOW HOW TO STORE OR
PRINT SENDER INFORMATION
You can store sender information in "Own Name and Destination Set" in
setting mode.
45
BROADCAST TRANSMISSION
DOES NOT WORK
Has broadcast setting been disabled in the setting mode
(administrator)?
45
THE DATA NOTIFICATION
INDICATOR DOES NOT TURN OFF
Is an error preventing received faxes from being printed?
46
I DON'T KNOW HOW TO CHECK AN
ADDRESS WHEN SENDING A FAX
Tap the [Address Review] key.
46
Is "Fax Dest. Confirmation Mode" enabled in setting mode?
46
TRANSMISSION DOES NOT TAKE PLACE
Check
Solution
Is the telephone line connected
securely?
Check the telephone line jack, the wall jack, and any extension adapters to make
sure that all connections are secure.
Power and connector positions
(page 4)
Is the correct dial mode set for your
line?
Ask your administrator to verify that "Dial Mode Setting" is set correctly for the
line you are using.
Select the telephone line type in "Dial Mode Setting" in the setting mode (administrator).
"Settings" → [System Settings] → [Image Send Settings]
→ [Fax Settings] → [
Condition Settings
] → [Dial Mode Setting]
Is a busy signal received?
If a busy signal is received, the transmission is temporarily canceled and then
automatically attempted again after a brief interval. The factory default setting :
Two attempts at 3-minute intervals.
"Settings"
[System Settings]
[Image Send Settings]
[Fax Settings]
[Send Setting]
[Recall in Case of Line Busy]
To cancel transmission, tap the job status display on the operation panel, tap
the key of the job you want to delete, and tap [Stop/Delete] on the action panel.
A message will appear to confirm the cancelation. Tap the [Cancel] key.
Did a communication error occur?
If an error occurs preventing transmission, the transmission is temporarily
canceled and then automatically re-attempted after a brief interval. The factory
default setting : Two attempts at 3-minute intervals.
"Settings (administrator)" →
[System Settings] → [Image Send Settings] →
[Fax Settings] → [Send Setting] → [Recall in Case of Communication Error]
To cancel transmission, tap the job status display on the operation panel, tap
the key of the job you want to delete, and tap [Stop/Delete] on the action panel.
A message will appear to confirm the cancelation. Tap the [Cancel] key.
The machine supports error correction mode (ECM) and is configured to
automatically resend any part of a fax that is distorted due to noise on the line.
"Settings"
[System Settings]
[Image Send Settings]
[Fax Settings]
[Default Settings]
[ECM]
Does a message appear indicating
that the memory is full?
Divide the originals into sets and fax each set separately, or use direct transmission.
If the memory becomes full, the transmission will be canceled.
Problem
Check
Page
?
?
!