Sony STR-D1090 Operating Instructions - Page 5

Unpacking

Get Sony STR-D1090 PDF manuals and user guides View all Sony STR-D1090 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

Chapter 1 Getting Started Unpacking Choosing a Good Location To prevent internal heat buildup in the unit, place the unit in a location with adequate air circulation. Do not install the unit: • near heat sources such as radiators or,air ducts. • in a place subject to direct sunlight, excessive dust, mechanical vibration or shock. Do not place anything on top of the cabinet. The top ventilation holes must be unobstructed for the proper operation of the unit and to prolong the life of its components. Do not throw away the carton and packing material! It will be an ideal container when transporting the system for repair work, etc. Checking the Supplied Accessories After unpacking, check that the following'accessories are present. • FM wire antenna (1) • AM loop antenna (1) • Remote commander RM-P321 (supplied with STR-D2090) (1) • Remote commander RM-U221 (supplied with STR-D1090) (1) • Sony batteries SUM-3 (NS) (2) To avoid damage caused by battery leakage and corrosion When the commander will not be used for a long time, remove the batteries. Battery life Normal operation can be expected about a half year using Sony SUM-3 (NS), and a year using Sony AM-3 (NW) alkaline batteries. When the batteries are run down, the remote commander will not operate the unit. In this case, replace batteries with new ones. Selecting the AM Tuning Interval The AM tuning interval is preset to 10 kHz. To use the receiver where the frequency allocation system is based on a 9 kHz interval, make the following adjustments. 1 Turn on the power and tune in any AM station. 2 Turn off the power. 3 Press the POWER button while pressing the "+" INDEX SELECT/TUNING button. To reset the AM tuning interval, repeat the above steps. Caution When the interval is changed, all preset stations which you have memorized will be erased. After changing the interval, be sure to preset the stations again. Inserting the Batteries into the Remote Commander Before operating remote commander, install the batteries as shown. 1 Open the cover. 2 Two size AA (R6) batteries with correct polarity. 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
Chapter
1
Getting
Started
Unpacking
Choosing
a
Good
Location
To
prevent
internal
heat
buildup
in
the
unit,
place
the
unit
in
a
location
with
adequate
air
circulation.
Do
not
install
the
unit:
•
near
heat
sources
such
as
radiators
or,
air
ducts.
•
in
a
place
subject
to
direct
sunlight,
excessive
dust,
mechanical
vibration
or
shock.
Do
not
place
anything
on
top
of
the
cabinet.
The
top
ventilation
holes
must
be
unobstructed
for
the
proper
operation
of
the
unit
and
to
prolong
the
life
of
its
components.
Do
not
throw
away
the
carton
and
packing
material!
It
will
be
an
ideal
container
when
transporting
the
system
for
repair
work,
etc.
Checking
the
Supplied
Accessories
After
unpacking,
check
that
the
following
'accessories
are
present.
•
FM
wire
antenna
(1)
•
AM
loop
antenna
(1)
•
Remote
commander
RM-P321
(supplied
with
STR-D2090)
(1)
•
Remote
commander
RM-U221
(supplied
with
STR-D1090)
(
1
)
•
Sony
batteries
SUM
-3
(NS)
(2)
Inserting
the
Batteries
into
the
Remote
Commander
Before
operating
remote
commander,
install
the
batteries
as
shown.
1
Open
the
cover.
2
Two
size
AA
(R6)
batteries
with
correct
polarity.
To
avoid
damage
caused
by
battery
leakage
and
corrosion
When
the
commander
will
not
be
used
for
a
long
time,
remove
the
batteries.
Battery
life
Normal
operation
can
be
expected
about
a
half
year
using
Sony
SUM
-3
(NS),
and
a
year
using
Sony
AM
-3
(NW)
alkaline
batteries.
When
the
batteries
are
run
down,
the
remote
commander
will
not
operate
the
unit.
In
this
case,
replace
batteries
with
new
ones.
Selecting
the
AM
Tuning
Interval
The
AM
tuning
interval
is
preset
to
10
kHz.
To
use
the
receiver
where
the
frequency
allocation
system
is
based
on
a
9
kHz
interval,
make
the
following
adjustments.
1
Turn
on
the
power
and
tune
in
any
AM
station.
2
Turn
off
the
power.
3
Press
the
POWER
button
while
pressing
the
"+"
INDEX
SELECT/TUNING
button.
To
reset
the
AM
tuning
interval,
repeat
the
above
steps.
Caution
When
the
interval
is
changed,
all
preset
stations
which
you
have
memorized
will
be
erased.
After
changing
the
interval,
be
sure
to
preset
the
stations
again.
5