Sony STR-DA4600ES Operating Instructions (Large File - 17.22 MB) - Page 50

When Error Code appears, To save measurement results, that caused an error without, taking a remedy

Get Sony STR-DA4600ES - 7.1 Channel Es Receiver PDF manuals and user guides View all Sony STR-DA4600ES manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

If a warning message appears, check the message and use the receiver without change. Or if necessary, perform auto calibration again. When "Error Code" appears Check the error and perform auto calibration again. 1 Press to select "Enter." 2 Press B/b to select "Retry," then press . 3 Repeat steps 6 to 7 in "Performing auto calibration" (page 47). To save measurement results that caused an error without taking a remedy 1 Press V/v to select "Save" in step 7 in "Performing auto calibration" (page 47), then press . 2 Follow the steps in "Saving the measurement results" (page 49) to save the measurement results. Message list after auto calibration measurement Display Explanation Code 30 Headphones are connected. Remove the headphones and perform auto calibration again. Code 31 SPEAKERS (A/B/A+B/OFF) is set to OFF. Set it to others and re-perform the measurement. Code 32 None of the speakers were detected. Make sure that the optimizer microphone is connected properly and reperform the measurement. If the optimizer microphone is connected properly but the error code appears, the optimizer microphone cable may be damaged or improperly connected. Code 33 • None of the front speakers are connected or only one front speaker is connected. • The optimizer microphone is not connected. • Either the left or right surround speaker is not connected. • Surround back speakers are connected even though surround speakers are not connected. Connect the surround speaker(s) to the SURROUND terminals. • The surround back speaker is connected only to the SURROUND BACK/FRONT HIGH/ ZONE 2 R terminals. When you connect only one surround back speaker, connect it to the SURROUND BACK/FRONT HIGH/ZONE 2 L terminals. • Only one front high speaker is connected. Connect the front high speaker to each of the SURROUND BACK/FRONT HIGH/ZONE 2 terminals. • Front high speakers are connected even though surround speakers are not connected. Connect the surround speaker(s) to the SURROUND terminals. Warning 40 The measurement has completed. However, the noise level is high. You may be able to perform the measurement properly if you try it again, even though the measurement cannot be performed in all environments. Try to perform the measurement in a quiet environment. Warning 41 Warning 42 The input from the microphone is too big. • It may be too close the distance between the speaker and the microphone. Retry the measurement after setting apart from each other. • When you use the receiver as a pre-amplifier, either messages may appear, depending the power amplifier you connect. However, there will be no problems, even if you continue to use the receiver without changes. Warning 43 The distance and position of a subwoofer cannot be detected. Or the angle of the speaker position cannot be detected. This may be caused by noise. Try to perform the measurement in a quiet environment. NO WARNING There is no warning information. ---------- No speakers are connected. 50GB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
50
GB
If a warning message appears, check the
message and use the receiver without change.
Or if necessary, perform auto calibration
again.
When “Error Code” appears
Check the error and perform auto calibration
again.
1
Press
to select “Enter.”
2
Press
B
/
b
to select “Retry,” then press
.
3
Repeat steps 6 to 7 in “Performing auto
calibration” (page 47).
To save measurement results
that caused an error without
taking a remedy
1
Press
V
/
v
to select “Save” in step 7 in
“Performing auto calibration” (page
47),
then press
.
2
Follow the steps in “Saving the
measurement results” (page 49) to
save the measurement results.
Message list after auto calibration measurement
Display
Explanation
Code 30
Headphones are connected. Remove the headphones and perform auto calibration again.
Code 31
SPEAKERS (A/B/A+B/OFF) is set to OFF. Set it to others and re-perform the measurement.
Code 32
None of the speakers were detected. Make sure that the optimizer microphone is connected
properly and reperform the measurement.
If the optimizer microphone is connected properly but the error code appears, the optimizer
microphone cable may be damaged or improperly connected.
Code 33
•
None of the front speakers are connected or only one front speaker is connected.
•
The optimizer microphone is not connected.
•
Either the left or right surround speaker is not connected.
•
Surround back speakers are connected even though surround speakers are not connected.
Connect the surround speaker(s) to the SURROUND terminals.
•
The surround back speaker is connected only to the SURROUND BACK/FRONT HIGH/
ZONE 2 R terminals. When you connect only one surround back speaker, connect it to the
SURROUND BACK/FRONT HIGH/ZONE 2 L terminals.
•
Only one front high speaker is connected. Connect the front high speaker to each of the
SURROUND BACK/FRONT HIGH/ZONE 2 terminals.
•
Front high speakers are connected even though surround speakers are not connected.
Connect the surround speaker(s) to the SURROUND terminals.
Warning 40
The measurement has completed. However, the noise level is high. You may be able to
perform the measurement properly if you try it again, even though the measurement cannot
be performed in all environments. Try to perform the measurement in a quiet environment.
Warning 41
Warning 42
The input from the microphone is too big.
•
It may be too close the distance between the speaker and the microphone.
Retry the measurement after setting apart from each other.
•
When you use the receiver as a pre-amplifier, either messages may appear, depending the
power amplifier you connect. However, there will be no problems, even if you continue to
use the receiver without changes.
Warning 43
The distance and position of a subwoofer cannot be detected. Or the angle of the speaker
position cannot be detected. This may be caused by noise. Try to perform the measurement
in a quiet environment.
NO WARNING
There is no warning information.
----------
No speakers are connected.