Sony VPL-FHZ120L Operating Instructions - Page 31

Set LAN Setting to LAN Port in HDBaseT Settings, then set the IP address in Network Setting.

Get Sony VPL-FHZ120L PDF manuals and user guides View all Sony VPL-FHZ120L manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Setting items Direct Power On Description On/Off: When you select "On" and plug the projector, the projection starts without going into standby mode. You can also unplug the AC power cord without going into standby mode when you turn off the projector. You may unplug the AC power cord without going into standby mode. *1: Set the IP address of this unit manually after connecting to the network. If this unit is not connected to the network, the setting is not enabled. *2: When connecting via HDBaseT, only the 100BASE-TX can be used for connection. When using the LAN terminal of the main unit, you can connect with the 10BASE-T/100BASE-TX/1000BASE-T. *3: The IP addresses when using HDBaseT and when using the LAN terminal should be set respectively.  Setting the IP address when using a LAN via HDBaseT. Set "LAN Setting" to "via HDBaseT" in "HDBaseT Settings," then set the IP address in "Network Setting."  Setting the IP address when using the LAN terminal. Set "LAN Setting" to "LAN Port" in "HDBaseT Settings," then set the IP address in "Network Setting." *4: If the image input setting of the HDMI connection device is not correct, the brighter part becomes too bright and the darker part becomes too dark. *5: Depending on the input video signal, the optimal signal type may not be selected. Set manually according to the connected device. *6: The "Auto Power Saving" function is not enabled for INPUT G. *7: Select "Off" to avoid entering standby mode when there is no input signal. *8: A change in signal may not be detected depending on the input image. If "With No Input" is set, it takes priority. *9: As the light is dimmed gradually, you may not notice any change in brightness. *10:This varies depending on the "Light Output Mode" setting (page 24). *11:When "Standby Mode" is set to "Low," the network and network control function cannot be operated while the projector is in standby mode. 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
31
*1:
Set the IP address of this unit manually after connecting to the network. If this unit is not connected to the network, the
setting is not enabled.
*2: When connecting via HDBaseT, only the 100BASE-TX can be used for connection. When using the LAN terminal of the
main unit, you can connect with the 10BASE-T/100BASE-TX/1000BASE-T.
*3: The IP addresses when using HDBaseT and when using the LAN terminal should be set respectively.
Setting the IP address when using a LAN via HDBaseT.
Set “LAN Setting” to “via HDBaseT” in “HDBaseT Settings,” then set the IP address in “Network Setting.”
Setting the IP address when using the LAN terminal.
Set “LAN Setting” to “LAN Port” in “HDBaseT Settings,” then set the IP address in “Network Setting.”
*4: If the image input setting of the HDMI connection device is not correct, the brighter part becomes too bright and the
darker part becomes too dark.
*5: Depending on the input video signal, the optimal signal type may not be selected. Set manually according to the
connected device.
*6: The “Auto Power Saving” function is not enabled for INPUT G.
*7:
Select “Off” to avoid entering standby mode when there is no input signal.
*8: A change in signal may not be detected depending on the input image. If “With No Input” is set, it takes priority.
*9: As the light is dimmed gradually, you may not notice any change in brightness.
*10:This varies depending on the “Light Output Mode” setting (page 24).
*11:When “Standby Mode” is set to “Low,” the network and network control function cannot be operated while the projector
is in standby mode.
Direct Power On
On/Off:
When you select “On” and plug the projector, the projection starts without going
into standby mode. You can also unplug the AC power cord without going into standby
mode when you turn off the projector.
You may unplug the AC power cord without going into standby mode.
Setting items
Description