Sony VPL-FHZ120L Operating Instructions - Page 47

Messages List

Get Sony VPL-FHZ120L PDF manuals and user guides View all Sony VPL-FHZ120L manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Messages List When any of the following messages appears on the projected image, solve the problem as shown in the next table. Message Description/Remedy Clean the filter. Projector temperature is high. Switching to High Altitude Mode. Temperature in the projector has increased. As a countermeasure against use at an altitude of 1,500 m or higher, set "High Altitude Mode" to "On." If you are not using the projector at a high altitude, perform the remedies below and set "High Altitude Mode" to "Auto" (page 33).  Check that the air filter is clogged, then clean or replace it (page 50).  Check that the ventilation holes (intake/exhaust) are not blocked by a wall or an object and secure a sufficient gap (page 4).  Check the ambient temperature and use the projector within the range of operating temperature (page 52). Clean the filter. Projector temperature is high. The light will turn off in 1 minute. Temperature in the projector has increased. Perform the remedies below.  Check that the air filter is clogged, then clean or replace it (page 50).  Check that the ventilation holes (intake/exhaust) are not blocked by a wall or an object and secure a sufficient gap (page 4).  Check the ambient temperature and use the projector within the range of operating temperature (page 52).  "High Altitude Mode" on this projector is set to "On." Set the setting that suits the operating environment. Frequency is out of range! Change the output setting of the connected device to one for signals supported by the projector (page 56). Please check Input-A Signal Sel. Set "Input-A Signal Sel." to "Auto" or select the input signal type to suit to the input signal (page 30). Not applicable! Press the appropriate key on the Remote Commander or control panel (page 6). The control keys are locked! "Control Key Lock" is set to "On" (page 29). Lens Control is locked! "Lens Control" is set to "Off" (page 29). Light Dimming Reduces light output when "With Static Signal" is set (page 30). When any change in signal is detected, or an operation (Remote Commander or control panel) is performed, normal brightness is restored. Constant Brightness cannot be maintained. Although "Constant Brightness" is selected, the brightness cannot be maintained due to the lifetime of the light source (page 24). Consult with qualified Sony personnel. Filter cleaning will start. Tapping sounds will occur. Turn off the projector and clean the air filter in standby mode (page 33). 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
47
Messages List
When any of the following messages appears on the projected image, solve the problem as shown in the
next table.
Message
Description/Remedy
Clean the filter.
Projector temperature is high.
Switching to High Altitude Mode.
Temperature in the projector has increased.
As a countermeasure against use at an altitude of 1,500 m or higher, set
“High Altitude Mode” to “On.”
If you are not using the projector at a high altitude, perform the remedies
below and set “High Altitude Mode” to “Auto” (page 33).
Check that the air filter is clogged, then clean or replace it (page 50).
Check that the ventilation holes (intake/exhaust) are not blocked by a wall
or an object and secure a sufficient gap (page 4).
Check the ambient temperature and use the projector within the range of
operating temperature (page 52).
Clean the filter.
Projector temperature is high. The light will
turn off in 1 minute.
Temperature in the projector has increased.
Perform the remedies below.
Check that the air filter is clogged, then clean or replace it (page 50).
Check that the ventilation holes (intake/exhaust) are not blocked by a wall
or an object and secure a sufficient gap (page 4).
Check the ambient temperature and use the projector within the range of
operating temperature (page 52).
“High Altitude Mode” on this projector is set to “On.” Set the setting that
suits the operating environment.
Frequency is out of range!
Change the output setting of the connected device to one for signals
supported by the projector (page 56).
Please check Input-A Signal Sel.
Set “Input-A Signal Sel.” to “Auto” or select the input signal type to suit to the
input signal (page 30).
Not applicable!
Press the appropriate key on the Remote Commander or control panel
(page 6).
The control keys are locked!
“Control Key Lock” is set to “On” (page 29).
Lens Control is locked!
“Lens Control” is set to “Off” (page 29).
Light Dimming
Reduces light output when “With Static Signal” is set (page 30). When any
change in signal is detected, or an operation (Remote Commander or control
panel) is performed, normal brightness is restored.
Constant Brightness cannot be maintained.
Although “Constant Brightness” is selected, the brightness cannot be
maintained due to the lifetime of the light source (page 24). Consult with
qualified Sony personnel.
Filter cleaning will start.
Tapping sounds will occur.
Turn off the projector and clean the air filter in standby mode (page 33).