Sony VPL-FHZ120L Operating Instructions - Page 40

Setting the Control Protocol of the Projector, Start Advertisement Service

Get Sony VPL-FHZ120L PDF manuals and user guides View all Sony VPL-FHZ120L manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

2 Set the Internet protocol in [Network Setting]. Via HDBaseT: Set the network settings for the HDBaseT terminal. LAN port: Set the network settings for the LAN port. 3 Set the items for Internet protocol. (a) IPv4/IPv6 address Obtain an IP address automatically (DHCP): Automatically provides the IP Address provided by a DHCP server. Specify an IP address: Set the network manually. -IP Address: Input the IP address of the projector. -Prefix: For IPv6, input the prefix (bit) of the projector. -Subnet Mask: Input the subnet mask of the projector. -Default Gateway: Input the default gateway of the projector. (b) DNS server Auto: Automatically provides the IP Address provided by a DHCP server. Manual -Primary DNS: Input the primary DNS server of the projector. -Secondary DNS: Input the secondary DNS server of the projector. 4 Set the items for Ethernet. MAC Address: Displays the MAC address of the projector. Note Different MAC addresses for the HDBaseT terminal or LAN port are provided to the projector. The DHCP server provides different IP addresses/ DNS for the HDBaseT terminal or LAN port. Setting the Control Protocol of the Projector Change the settings for the control protocol on the Setup page. Entered values will not be applied unless you click on [Apply]. 1 Click on [Advanced Menu] to display the Setup page. Advanced Menu button 2 Click on [Advertisement] to display the Advertisement page. Advertisement button Start Advertisement Service: Set Advertisement to enabled or disabled. Items for Advertisement are enabled only when this function is enabled. The function is enabled at the factory default. -Community: Input the community name for Advertisement and PJ Talk. If the community name for Advertisement is changed, the one for PJ Talk will also be changed. Only four alphanumeric characters can be input. The factory default setting is "SONY." To avoid unwanted access to the projector from other computers, changing the community name of the factory default is recommended. -Port No.: Input the transmit port of Advertisement. The factory default setting is "53862." -Interval: Input the transmission interval (seconds) of Advertisement. The factory default setting is "30." -Broadcast Address: Input the destination of data via Advertisement. If nothing is input, the data will be broadcast in the same subnetwork. 40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
40
2
Set the Internet protocol in [Network Setting].
Via HDBaseT:
Set the network settings for the
HDBaseT terminal.
LAN port:
Set the network settings for the
LAN port.
3
Set the items for Internet protocol.
(a) IPv4/IPv6 address
Obtain an IP address automatically (DHCP):
Automatically provides the IP Address
provided by a DHCP server.
Specify an IP address:
Set the network
manually.
-IP Address:
Input the IP address of the
projector.
-Prefix:
For IPv6, input the prefix (bit) of the
projector.
-Subnet Mask:
Input the subnet mask of the
projector.
-Default Gateway:
Input the default gateway
of the projector.
(b) DNS server
Auto:
Automatically provides the IP Address
provided by a DHCP server.
Manual
-Primary DNS:
Input the primary DNS server
of the projector.
-Secondary DNS:
Input the secondary DNS
server of the projector.
4
Set the items for Ethernet.
MAC Address:
Displays the MAC address of
the projector.
Different MAC addresses for the HDBaseT terminal
or LAN port are provided to the projector.
The DHCP server provides different IP addresses/
DNS for the HDBaseT terminal or LAN port.
Change the settings for the control protocol on the
Setup page.
Entered values will not be applied unless you click
on [Apply].
1
Click on [Advanced Menu] to display the Setup
page.
2
Click on [Advertisement] to display the
Advertisement page.
Start Advertisement Service:
Set
Advertisement to enabled or disabled.
Items for Advertisement are enabled only
when this function is enabled. The function
is enabled at the factory default.
-Community:
Input the community name for
Advertisement and PJ Talk. If the
community name for Advertisement is
changed, the one for PJ Talk will also be
changed. Only four alphanumeric
characters can be input. The factory default
setting is “SONY.” To avoid unwanted
access to the projector from other
computers, changing the community name
of the factory default is recommended.
-Port No.:
Input the transmit port of
Advertisement. The factory default setting
is “53862.”
-Interval:
Input the transmission interval
(seconds) of Advertisement. The factory
default setting is “30.”
-Broadcast Address:
Input the destination of
data via Advertisement. If nothing is input,
the data will be broadcast in the same
subnetwork.
Note
Setting the Control Protocol of the Projector
Advanced Menu button
Advertisement button