Stihl FS 560 C-EM Product Instruction Manual - Page 29

attachment's mounting hole b.

Page 29 highlights

681BA165 KN 002BA471 KN Removing the cutting attachment N Block the drive shaft. N Unscrew the mounting nut clockwise. N Pull the cutting attachment with its mounting hardware off the gearbox. Mounting circular saw blades 225 N Check that the stop for circular saw blades is already mounted to the machine - if not, perform the next two steps. N Remove grass shield - if fitted. N Remove deflector - if fitted. N Mount limit stop for circular saw blades. N Use the 2.6-in (65-mm) diameter thrust plate. The cutting edges of circular saw blades must point clockwise. 4 3 2 1 b a N Place the cutting attachment (1) in position. Collar (a) must locate in the cutting attachment's mounting hole (b). N Fit the 2.4-in (60-mm) diameter thrust washer (2) - convex side must face up. N Fit the 2.5-in (63-mm) diameter rider plate (3). N Block the drive shaft. N Screw on the nut (4) counterclockwise and tighten it down firmly. English Removing the cutting attachment N Block the drive shaft. N Unscrew the mounting nut clockwise. N Pull the cutting attachment with its mounting hardware off the gearbox. FS 510 C-M, FS 560 C-M 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120

FS 510 C-M, FS 560 C-M
English
27
Removing the cutting attachment
N
Block the drive shaft.
N
Unscrew the mounting nut
clockwise.
N
Pull the cutting attachment with its
mounting hardware off the gearbox.
Mounting circular saw blades 225
N
Check that the stop for circular saw
blades is already mounted to the
machine – if not, perform the next
two steps.
N
Remove grass shield – if fitted.
N
Remove deflector – if fitted.
N
Mount limit stop for circular saw
blades.
N
Use the 2.6-in (65-mm) diameter
thrust plate.
The cutting edges of circular saw blades
must point clockwise.
N
Place the cutting attachment (1) in
position.
Collar (a) must locate in the cutting
attachment's mounting hole (b).
N
Fit the 2.4-in (60-mm) diameter
thrust washer (2) – convex side
must face up.
N
Fit the 2.5-in (63-mm) diameter rider
plate (3).
N
Block the drive shaft.
N
Screw on the nut (4)
counterclockwise and tighten it
down firmly.
Removing the cutting attachment
N
Block the drive shaft.
N
Unscrew the mounting nut
clockwise.
N
Pull the cutting attachment with its
mounting hardware off the gearbox.
681BA165 KN
2
1
4
002BA471 KN
3
b
a