Stihl FS 560 C-EM Product Instruction Manual - Page 38

Spark Plug

Get Stihl FS 560 C-EM PDF manuals and user guides View all Stihl FS 560 C-EM manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

4900BA021 KN 4900BA022 KN English 2 5 4 The cover plate kit contains the following parts for converting the power tool: 4 Cover plate partially blanks off the slots in the starter housing 5 Synthetic fabric filter element for the air filter - Instructions for converting the machine After installing the cover plate kit: N Set the shutter (2) to the winter position. At temperatures above +14°F (-10°C) N Clean away loose dirt from around the filter (5) and inside the filter cover. N Knock the filter (5) out on the palm of your hand or blow it clear with compressed air from the inside outwards. In case of stubborn dirt or sticky filter fabric: N Wash the filter in a clean, nonflammable solution (e.g. warm soapy water) and then dry. Always replace a damaged filter. N Remove the parts of the cover plate kit and refit the standard parts for summer operation. Depending on the ambient temperature: N Set the shutter (2) to the summer or winter position. Cleaning the Air Filter N Loosen filter cover mounting screws. N Remove the filter cover. Spark Plug If engine is down on power, difficult to start or runs poorly at idling speed, first check the spark plug. Fit a new spark plug after approx. 100 operating hours or earlier if the electrodes are badly eroded. Wrong fuel mix (too much engine oil in the gasoline), a dirty air filter and unfavorable running conditions (mostly at part throttle etc.) affect the condition of the spark plug. These factors cause deposits to form on the insulator nose which may result in trouble in operation. Removing the Spark Plug 1 N Rotate the screw (1) in the cap (2) until the screw head projects from it. 36 FS 510 C-M, FS 560 C-M

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
FS 510 C-M, FS 560 C-M
English
36
The cover plate kit contains the following
parts for converting the power tool:
4
Cover plate partially blanks off the
slots in the starter housing
5
Synthetic fabric filter element for the
air filter
–
Instructions for converting the
machine
After installing the cover plate kit:
N
Set the shutter (2) to the winter
position.
At temperatures above +14°F (
-
10°C)
N
Remove the parts of the cover plate
kit and refit the standard parts for
summer operation.
Depending on the ambient temperature:
N
Set the shutter
(2) to the summer or
winter position.
Cleaning the Air Filter
N
Loosen filter cover mounting
screws.
N
Remove the filter cover.
N
Clean away loose dirt from around
the filter (5) and inside the filter
cover.
N
Knock the filter (5) out on the palm
of your hand or blow it clear with
compressed air from the inside
outwards.
In case of stubborn dirt or sticky filter
fabric:
N
Wash the filter in a clean, non-
flammable solution (e.g. warm
soapy water) and then dry.
Always replace a damaged filter.
If engine is down on power, difficult to
start or runs poorly at idling speed, first
check the spark plug.
Fit a new spark plug after approx. 100
operating hours
or earlier if the
electrodes are badly eroded.
Wrong fuel mix (too much engine oil in
the gasoline), a dirty air filter and
unfavorable running conditions (mostly
at part throttle etc.) affect the condition
of the spark plug. These factors cause
deposits to form on the insulator nose
which may result in trouble in operation.
Removing the Spark Plug
N
Rotate the screw (1) in the cap (2)
until the screw head projects from it.
4900BA021 KN
4
2
5
Spark Plug
4900BA022 KN
1